Checking PC Specs

How to Check the Maximum RAM Your Motherboard Supports

Find your motherboard's maximum RAM from the manufacturer's memory specs, then check your CPU, Windows edition, and slot count, since the lowest limit wins.

On this page
  1. Short answer
  2. Why there is more than one limit
  3. Step 1: Find your motherboard model
  4. Step 2: Check the manufacturer’s memory specs
  5. Step 3: Check the CPU’s memory limit
  6. Step 4: Check your Windows edition
  7. Step 5: Count your memory slots
  8. Rough math: slots times largest module
  9. Check the software reading, but don’t rely on it
  10. Match the memory type and speed
  11. Other things to check
  12. Safety

Short answer

Look up your exact motherboard model on the manufacturer’s website and read its memory specifications. They list the maximum capacity, the number of memory slots, and the supported memory type. Then confirm the total against your CPU’s memory limit and your Windows edition. The lowest of these limits is the one you can use.

Why there is more than one limit

Three things cap the RAM a PC can use:

  • The CPU: Its memory controller sets a maximum. Check the processor’s spec page on Intel’s or AMD’s website.
  • The motherboard: Its slots and BIOS set the total limit and the largest module each slot accepts.
  • The operating system: Windows 10 and 11 Home support up to 128 GB, and Windows 10 and 11 Pro support up to 2 TB. 32-bit Windows is limited to about 4 GB.

For example, if a CPU supports 192 GB but the board’s manual lists 128 GB, the usable limit is 128 GB.

Step 1: Find your motherboard model

You need the exact model name, not the chipset. Open msinfo32 and check BaseBoard Product, or run this in PowerShell:

Get-CimInstance -ClassName Win32_BaseBoard | Select-Object Product

For more ways to find the model, see how to find your motherboard model and serial number. A chipset name such as B650 or Z790 isn’t the model. The full model is more specific, such as “MAG B650 TOMAHAWK WIFI.”

Step 2: Check the manufacturer’s memory specs

On the board’s product page, look for the Memory or Specifications section, and note these:

  • Maximum capacity for the whole board
  • Number of DIMM slots
  • Memory type (DDR4 or DDR5) and the supported speeds
  • QVL (Qualified Vendor List), which shows the memory kits the manufacturer has tested with the board

If the spec lists larger modules than your current BIOS recognizes, a BIOS update may be needed. Check the board’s support page.

Step 3: Check the CPU’s memory limit

Find your processor on Intel’s or AMD’s product page, and look for the maximum memory size and the supported memory types. A board can’t use more RAM than the CPU’s memory controller supports, so the CPU’s number can be lower than the board’s.

Step 4: Check your Windows edition

Open Settings > System > About and look at the Edition under Windows specifications. The limits are:

  • Windows 10 and 11 Home: 128 GB
  • Windows 10 and 11 Pro: 2 TB (workstation editions allow more)
  • 32-bit Windows: about 4 GB

If you’re on a 32-bit version, see how to find out x64 or x86.

Step 5: Count your memory slots

Open Task Manager (Ctrl + Shift + Esc), select Performance, then Memory. The Slots used: X of Y line shows how many slots are filled out of the total. Most consumer boards have two or four DIMM slots. For the rest of your hardware details, see how to check your PC specs.

Rough math: slots times largest module

As a rough estimate, multiply the number of slots by the largest module the board supports. A four-slot board that supports 32 GB modules would top out at 128 GB. Not every board supports the largest module in every slot, so confirm the figure in the manufacturer’s spec.

These are typical figures, and they vary by board and BIOS:

  • DDR4 consumer boards often top out at 128 GB (4 × 32 GB).
  • DDR5 platforms are often rated for 192 GB (4 × 48 GB). Some newer boards have reached 256 GB (4 × 64 GB) after BIOS updates, so check the manufacturer’s notes.

DDR5 also comes in 24 GB and 48 GB modules, so a four-slot board with 48 GB modules can reach 192 GB.

Check the software reading, but don’t rely on it

Software can report a maximum capacity, but those numbers can be wrong or out of date.

  • PowerShell: Get-CimInstance Win32_PhysicalMemoryArray | Select-Object MaxCapacity, MemoryDevices. MaxCapacity is in kilobytes, so divide by 1,048,576 to get gigabytes.
  • Command Prompt (if WMIC is available): wmic memphysical get maxcapacity also returns kilobytes.
  • Linux: sudo dmidecode -t memory lists “Maximum Capacity” and “Number Of Devices.”

Match the memory type and speed

Other things to check

  • Older boards may need a BIOS update before they recognize larger modules.
  • Laptops and mini PCs use SO-DIMM modules, and some have memory that is partly or fully soldered to the board, so they can’t always be upgraded.
  • CPU-Z has an SPD tab that shows the module installed in each slot, which helps when you’re counting slots and sizes.

Safety

Power off and unplug the PC, then touch grounded metal before you install memory. Hold each module by its edges.

The complete guide to checking pc specs

How to Check Your PC Specs and Identify Hardware
Read the guide

Keep exploring

Guides from other topics

All topics →