The BIOS (now usually UEFI) is the firmware screen your motherboard shows before Windows starts. It is where you set up memory speed, boot order, Windows 11 security features and fan curves. This guide covers how to get in, which settings to check first after a build, and where to find the detailed guide for each one.
How to enter the BIOS
Power on or restart the PC and press Delete or F2 right away, before the Windows logo appears. On most ASUS, MSI, Gigabyte and ASRock boards, Delete is the key. F2 also works on many ASUS and ASRock boards.
Pre-built PCs use other keys. HP usually uses F10 or Esc, Lenovo often uses F2 or F1 on desktops, and Dell uses F2 or F12. Check the start-up screen for the key it lists.
If your key presses do nothing, Fast Boot may be skipping the key window. Use a wired keyboard, since some wireless keyboards don’t connect until Windows loads. You can also open the BIOS from Windows: go to Settings > System > Recovery, click Restart now next to Advanced startup, then choose Troubleshoot > Advanced options > UEFI Firmware Settings. An administrator Command Prompt can also run shutdown /r /fw /t 0.
EZ Mode and Advanced Mode
On ASUS boards, the BIOS opens in EZ Mode, which shows the basics. Press F7 to switch to Advanced Mode, where most of the options live. F5 loads Optimized Defaults, and F10 saves and exits.
Change one setting at a time and write down the original value. That makes it easy to undo a change that causes problems.
Settings to check after a build
Start by confirming that the CPU, RAM capacity and drives are detected. Then check these settings:
- Memory profile. Turn on XMP for Intel-rated RAM or EXPO for AMD-rated RAM. RAM doesn’t run at its rated speed until you do. The enable XMP or EXPO guide covers the steps.
- Boot order. Set your OS drive first, or use the one-time boot menu to start from a USB drive. The boot order guide explains both.
- Windows 11 security. Windows 11 needs TPM 2.0 and works best with Secure Boot on. Turn on TPM with the TPM 2.0 guide, and Secure Boot with the Secure Boot guide.
- Virtualization. Turn on VT-x or SVM Mode if you use WSL 2, Docker, VirtualBox or an emulator. On AMD, SVM Mode is often off by default. The virtualization guide shows the path.
- Resizable BAR. Enable Above 4G Decoding and Re-Size BAR Support if your GPU and CPU support it. See the Resizable BAR guide.
- Fan curves. Set the fan curves for your CPU and case so the fans respond to heat without running loud at idle.
Settings to handle with care
Some settings change how hard the CPU works or how the PC uses standby power. Read about them before you change them:
- ASUS Performance Enhancement raises the CPU’s power limits. It can add a little performance and a lot of heat, so it needs a good cooler. See what ASUS performance enhancement is.
- ErP Ready cuts standby power and some wake features while the PC is off. See should you enable ErP in BIOS before you decide.
- Intel 13th and 14th generation CPUs should use Intel’s default power settings rather than unlimited MultiCore Enhancement, for long-term stability.
Keep the BIOS up to date
Check your current version with msinfo32, then read the release notes before you update. Update only when a new version fixes something you need. For a general overview, see how to update your motherboard BIOS. For brand-specific steps, use how to update asus motherboard BIOS or how to update BIOS on a Gigabyte motherboard.
Never power off during a flash, and suspend BitLocker first.
When to clear the CMOS
Clear CMOS when the BIOS is stuck, you can’t reach it, or the board won’t start after a bad change (for a new build that won’t start at all, see how to diagnose a DOA motherboard). Clearing CMOS also resets the clock and boot order. The CMOS battery and RTC guide shows the button, pin and battery methods.
For a normal settings change, use Load Optimized Defaults (F5) instead. You don’t need to clear CMOS to undo it.
Common misconceptions
- Load Optimized Defaults turns off XMP and EXPO. Turn the memory profile back on afterwards.
- Every BIOS option needs tuning. Defaults are fine for most of them. Change the options that matter for your build.
- BIOS and UEFI are different screens. On current boards, they are the same firmware screen with different names.
- Clearing CMOS is needed for every change. It isn’t. Load Optimized Defaults is the usual way to undo a change.