The CMOS battery is a CR2032 coin cell on the motherboard. It keeps the real-time clock (RTC) and some BIOS memory running when the PC has no power. Replace it when the date resets at every boot or the board shows a battery warning. To reset the BIOS, you can use the clear CMOS button, short the CLRTC pins, or remove the battery.
The short answer
The battery is a CR2032, not a CR2025. When the clock resets at every power-on, replace it. To reset the BIOS, switch off the PSU and unplug it first. Then use the clear CMOS button, the CLRTC pins or remove the battery for at least five minutes. After any reset, set the date and time and load Optimized Defaults.
What the RTC and CMOS battery do
The RTC is a clock chip in the chipset (Intel PCH or AMD FCH). It keeps time with a 32.768 kHz crystal. The CMOS memory stores BIOS settings such as the date, time and boot order.
The battery is a 3 V lithium CR2032 coin cell, typically around 220 to 240 mAh. It supplies power to the RTC and CMOS memory when the PC has no standby power, which means when the PSU is off or unplugged. It does not power the PC and does not charge while the PC runs.
A typical cell lasts about 3 to 10 years. Many modern UEFI boards store settings in flash memory, so a dead battery may reset only the clock. The exact behaviour varies by board.
Where the battery is
On most desktop boards, the battery sits in the lower half of the board, near the PCIe slots. It is often under the graphics card, so you may need to remove the card to reach it.
Some boards hide it under an M.2 heatsink or a chipset cover. Mini-ITX boards often use a wired, wrapped cell with a small plug instead of an open clip. Laptops usually tuck it under the bottom cover.
Signs the battery is failing
- The date and time reset at every power-on.
- Messages such as “CMOS checksum error” or “CMOS battery failure” appear at boot. Press F1 to continue, then reset the clock.
- BIOS settings such as boot order reset more often than usual.
These resets are easy to mistake for a failing board. The symptoms of a bad motherboard help you tell the two apart.
A wrong clock causes problems beyond the BIOS. HTTPS certificate checks and some sign-ins fail when the date is wrong.
A fresh cell reads about 3.0 to 3.3 V. Replace it once it reads below about 2.8 V. The threshold is approximate, so check the cell with a multimeter if you have one.
A dead battery rarely stops the PC from booting. It starts with default settings and the clock is wrong.
How to replace the CMOS battery
- Shut the PC down, switch off the PSU and unplug the power cable.
- Press the power button for about 10 seconds to drain any remaining charge.
- Touch the metal case to discharge static before you touch the board.
- Find the battery. Remove the graphics card if it’s in the way.
- Press the clip or pull the tab to release the old cell.
- Insert the new CR2032 with the + side facing up. Press it into the holder until the clip holds it.
- Reconnect the power, power on, and enter the BIOS. Set the date and time, then load Optimized Defaults.
How to clear CMOS
Power off and unplug the PSU before any of these methods.
- Clear CMOS button. Some boards have one on the rear I/O. Press and hold it for about 5 to 10 seconds, then power on.
- CLRTC pins. Look for CLRTC, CLR_CMOS or JBAT1 on the board. Short the two pins with a metal jumper cap or a screwdriver for 5 to 10 seconds, then power on.
- Battery removal. Take the cell out and wait at least five minutes. Some boards need longer. Put it back in and power on.
After any reset, the BIOS may ask you to confirm. On ASUS boards, press F1 to enter the BIOS, press F5 to load Optimized Defaults, then press F10 to save and exit.
Clearing CMOS doesn’t happen instantly when you remove the battery, because the standby power and capacitors need time to drain. You don’t need to clear CMOS to undo a normal settings change. Use Load Optimized Defaults for that.
After a reset
Set the date and time. Then turn your settings back on:
- Re-enable XMP or EXPO for your RAM.
- Check the boot order, since a reset can change it. How to change boot order in BIOS explains the options.
- Set fan curves if you use them.
If the screen stays black after a BIOS update and clearing CMOS doesn’t help, see how to update asus motherboard BIOS.
Safety
- A swallowed coin cell can cause serious internal burns quickly. Keep cells away from children and pets. If someone swallows one, get emergency medical help straight away.
- Unplug the PSU before you touch anything inside the PC.
- Use a CR2032. A CR2025 fits in the holder, but it’s thinner and has less capacity, so it may not make reliable contact.
For the other settings to check after a reset or build, see the BIOS settings guide.