BIOS Settings

How to Enable XMP or EXPO in BIOS

Turn on XMP (Intel), EXPO or DOCP (AMD) in an ASUS BIOS so your RAM runs at its rated speed. Menu paths, option choices, and how to check the speed.

On this page
  1. The short answer
  2. What XMP and EXPO do
  3. Before you start
  4. Turn the profile on in an ASUS BIOS
  5. XMP I, XMP II and EXPO options
  6. Check that RAM runs at its rated speed
  7. If the PC won’t boot or is unstable
  8. Common mistakes

Memory kits ship with a fast speed on the label, but a fresh PC usually runs RAM at a slower default until you turn on the memory profile. On an ASUS board, that means enabling XMP, EXPO or DOCP in the BIOS. It takes about five minutes.

The short answer

Restart and enter the BIOS. In Advanced Mode, go to Ai Tweaker > Ai Overclock Tuner and choose the profile your kit supports. Pick XMP I for Intel-rated kits, or EXPO I (or DOCP on boards that show it) for AMD-rated kits. Save with F10, let the PC restart, then check the speed in Windows.

What XMP and EXPO do

XMP (Extreme Memory Profile) is Intel’s name for a memory profile. EXPO (Extended Profiles for Overclocking) is AMD’s version. A profile is stored on the RAM itself and sets the speed, timings and voltage for the kit.

Without a profile, RAM runs at JEDEC defaults. DDR4 usually runs at 2133 or 2400 MT/s, and DDR5 usually at 4800 MT/s. The profile is what gets you to the rated speed. Even on “Auto” settings, the rated speed is not used until you enable the profile.

ASUS may label the AMD-side option DOCP, depending on the board and BIOS version. Many kits carry both XMP and EXPO profiles.

Before you start

  • Check the label or box for XMP, EXPO or both, and the rated speed.
  • Look up your kit on the board’s QVL (qualified vendor list) on the ASUS support site. A kit on the list is more likely to work at its rated speed.
  • Install the RAM in the slots the motherboard manual recommends for your number of sticks.
  • If the kit is new and the board is older, a newer BIOS can improve memory compatibility. See how to update asus motherboard BIOS before you tune memory.

Turn the profile on in an ASUS BIOS

  1. Power on and press Delete or F2 until the BIOS opens.
  2. In EZ Mode, look for the DRAM Status section. The X.M.P. setting is there on many boards. You can also press F7 for Advanced Mode.
  3. In Advanced Mode, go to Ai Tweaker and set Ai Overclock Tuner to the profile you want.
  4. Press F10 to save and restart.

XMP I, XMP II and EXPO options

The “I” and “II” options apply the profile in slightly different ways. Option I is the usual first try. It loads ASUS’s optimised memory settings. Option II loads the profile stored on the memory itself. The wording varies by BIOS version.

If the PC won’t start with one option, try the other. If neither is stable, reset the CMOS and try a lower speed.

Check that RAM runs at its rated speed

Open Task Manager, go to Performance, then Memory. The Speed figure is in MT/s, so a DDR5-6000 kit should show 6000.

CPU-Z shows half of that number for DDR5, so it lists 3000 MHz for DDR5-6000. This is normal and not a fault.

After you change the profile, run a memory test such as MemTest86 or TestMem5. If it reports errors, step the speed down one level and test again.

If the PC won’t boot or is unstable

  • The first boot after a memory change can take several minutes while the board trains the memory. A blank screen during this time is not always a fault.
  • If it still won’t start, clear the CMOS (see CMOS battery and RTC) and try a lower profile.
  • On DDR5, four sticks often can’t hold the rated speed. Two sticks are usually the more stable choice.
  • Some Ryzen 7000 and 9000 systems run DDR5-6000 well, but the best speed depends on the chip. Test before you push higher.

Common mistakes

  • Auto does not mean XMP or EXPO. Profiles are off by default.
  • Load Optimized Defaults (F5) turns the profile off again, so re-enable it afterwards.
  • Mixing two different kits does not reliably run either kit’s profile.
  • Don’t raise DRAM voltage above the kit’s rated profile voltage without researching safe limits. For reference, JEDEC defaults are about 1.2 V for DDR4 and 1.1 V for DDR5. Profile voltages are higher and vary by kit.

For the rest of the setup, the BIOS settings guide covers the other options to check after a build.

The complete guide to bios settings

BIOS Settings Guide: How to Enter BIOS and What to Change
Read the guide

Keep exploring

Guides from other topics

All topics →