RAM

DDR5 RAM Speeds: MT/s List and What to Buy

DDR5 speed list in MT/s, from JEDEC bins to common EXPO and XMP kits, with platform limits, four-stick caveats, and what to buy for AM5 or Intel.

On this page
  1. What MT/s means
  2. JEDEC DDR5 speed bins
  3. Common XMP and EXPO kit speeds
  4. What your CPU and board support
  5. Why 6000 CL30 is a common pick
  6. Higher speeds and the memory controller
  7. Four sticks
  8. Turning on EXPO or XMP
  9. What to buy
  10. Common misconceptions

DDR5 speeds are rated in MT/s, and the JEDEC standard covers 3200 to 8800 MT/s. For most AM5 builds, a DDR5-6000 CL30 kit is the common choice, because it runs at the memory controller’s 1:1 sweet spot. Your CPU and motherboard set the real limit, so check their support before you buy.

What MT/s means

MT/s stands for megatransfers per second. DDR5 moves data on both edges of the clock, so the clock runs at half the MT/s figure. A DDR5-6000 kit has a 3000 MHz clock.

The clock matters when you compare kits by latency. Convert CAS latency (CL) to nanoseconds with CL × 2000 ÷ MT/s. For why this matters, see RAM timings and latency.

JEDEC DDR5 speed bins

These are the standard JEDEC speed bins. Their timings are loose: DDR5-4800 is specified at CL40, and DDR5-5600 at CL46.

Speed (MT/s) Clock (MHz)
3200 1600
3600 1800
4000 2000
4400 2200
4800 2400
5200 2600
5600 2800
6000 3000
6400 3200
6800 3400
7200 3600
7600 3800
8000 4000
8400 4200
8800 4400

Common XMP and EXPO kit speeds

Most DDR5 kits sold today run on an XMP (Intel) or EXPO (AMD) profile rather than the JEDEC defaults. The common ones are:

Speed (MT/s) Typical CL
5600 CL36 or CL40
6000 CL30 or CL36
6400 CL32
7200 CL34
8000 CL38

A kit’s profile sets its rated speed and timings in one step. Without the profile enabled, the kit typically runs at the JEDEC default, often 4800 MT/s.

What your CPU and board support

These are the official memory speeds for each platform:

  • Intel 12th gen: DDR5-4800
  • Intel 13th and 14th gen: DDR5-5600
  • Intel Core Ultra 200S: DDR5-6400
  • AMD Ryzen 7000: DDR5-5200
  • AMD Ryzen 9000: DDR5-5600 with two DIMMs

Many boards and CPUs run higher with an EXPO or XMP profile, but that is not guaranteed. Check your motherboard’s memory support list (the QVL) before you buy a fast kit.

Why 6000 CL30 is a common pick

On AM5, DDR5-6000 CL30 runs with the memory controller clock (UCLK) at a 1:1 ratio with the memory clock, and with FCLK near 2000 MHz. That combination keeps latency low. The first-word latency works out to 10 ns.

Some AM5 chips run 6200 or 6400 at 1:1, but results vary by CPU. On Intel 13th and 14th gen, 6400 to 7200 MT/s is typical on good boards, depending on the CPU.

Higher speeds and the memory controller

On AM5, speeds above about 6400 MT/s usually move the controller to a 1:2 ratio, which adds latency. An 8000 MT/s kit at 1:2 performs roughly like a 6000 MT/s kit at 1:1, so a bigger number does not automatically mean faster.

Intel Core Ultra 200S (Arrow Lake) can reach 8000 to 8800 MT/s with CUDIMM modules, which carry a clock driver on the module itself.

Four sticks

Four DDR5 sticks put more load on the memory controller than two. Four-DIMM builds are typically limited to around 4800 to 5600 MT/s, and a kit’s rated speed often does not run with four sticks installed. If your goal is 6000 MT/s, two sticks are the easier path.

Turning on EXPO or XMP

Enable the EXPO profile (AMD) or XMP 3.0 profile (Intel) in the BIOS to run the rated speed. After you restart, check the speed in CPU-Z or the BIOS. If the system won’t boot at the profile speed, lower the speed one step, or raise the DRAM voltage slightly within the kit’s rated range. Typical profile voltages sit between 1.25 and 1.40 V.

What to buy

  • Capacity: two matching sticks. 2×16 GB (32 GB) suits most gaming and creative work. 2×32 GB (64 GB) suits heavier editing, virtual machines and local AI work.
  • AM5: DDR5-6000 CL30 is the simplest route to the sweet spot.
  • Intel: choose a speed your CPU and board support. 6400 to 7200 MT/s is a common target on good boards.
  • Chips: SK Hynix A-die and M-die chips generally clock highest, while Samsung and Micron typically clock lower. The chip type is listed in detailed reviews and manufacturer specs.
  • Price: DDR5 prices rose sharply over 2025 and 2026, and the best-value speed moves with the market. Compare current prices before you buy.

Common misconceptions

  • “DDR5-6000 runs at 6000 MHz.” It is rated in MT/s. The clock is 3000 MHz.
  • “Faster is always better on AM5.” Beyond the 1:1 range, latency rises.
  • “Four sticks will run at the kit’s rated speed.” Often they will not.
  • “DDR5 has ECC.” DDR5 has on-die ECC, which corrects errors inside the chip. It is not the system-level ECC that server memory provides.
  • “Higher speeds don’t need BIOS changes.” Enable the EXPO or XMP profile to get the rated speed.

For the DDR4 equivalent, see DDR4 RAM speeds, and for the basics of each generation, see the PC RAM guide.

The complete guide to ram

PC RAM Guide: Module Types, Specs and How Much You Need
Read the guide

Keep exploring

Guides from other topics

All topics →