RAM

DDR4 RAM Speeds: Frequency List and What to Buy

DDR4 RAM speeds from the JEDEC 1600-3200 MT/s baseline to XMP overclock profiles, with the actual clock, latency, and what to buy for your platform.

On this page
  1. DDR4 speed list
  2. MT/s and MHz
  3. What your platform supports
  4. What to buy
  5. Why CL matters too
  6. Turning on the speed you paid for
  7. Is DDR4 still worth buying?
  8. Common misconceptions

DDR4 runs at speeds from 1600 to 3200 MT/s under the JEDEC standard, and enthusiast kits go well beyond that through XMP profiles. For most builds on an existing DDR4 platform, a 3600 MT/s kit with CL16 or CL18 is the usual target, but the right speed depends on your CPU and board.

DDR4 speed list

The table below lists the standard JEDEC speeds, the PC4 name each one is sold under, and the actual clock. Remember that the clock is half the MT/s figure.

Speed (MT/s) PC4 name Clock (MHz) Type
1600 PC4-12800 800 JEDEC
1866 PC4-14900 933 JEDEC
2133 PC4-17000 1066 JEDEC
2400 PC4-19200 1200 JEDEC
2666 PC4-21300 1333 JEDEC
2933 PC4-23466 1467 JEDEC
3200 PC4-25600 1600 JEDEC
3600 PC4-28800 1800 XMP / overclock
4000 PC4-32000 2000 XMP / overclock
4400 PC4-35200 2200 XMP / overclock

Speeds above 3200 MT/s are not JEDEC standards. They are overclocked profiles (XMP, or DOCP on some AMD boards) that the kit maker validates. Some very high kits go to 4800 MT/s and beyond, but these are aimed at enthusiasts who will tune them by hand.

MT/s and MHz

MT/s stands for megatransfers per second. DDR transfers data on both edges of the clock, so the clock is half the MT/s number. A DDR4-3600 kit runs its clock at 1800 MHz. If you see “1800” in CPU-Z, that is the same kit.

What your platform supports

Your CPU and motherboard set the ceiling. The kit’s rating is not guaranteed.

  • Intel: official DDR4 support rises with each generation, from 2133 MT/s on 6th gen to 3200 MT/s on 11th to 14th gen. The exact limit depends on the chip and the board.
  • AMD Ryzen 3000 and 5000 (AM4): official support is 3200 MT/s. The sweet spot is 3600 MT/s with CL16, which runs the memory clock and the Infinity Fabric clock (FCLK) at a 1:1 ratio at 1800 MHz.

On Ryzen, faster is not always better. Past the FCLK limit, the chip drops to a 2:1 ratio, which raises latency and can make a faster kit slower in practice. Many Zen 3 chips reach a higher FCLK, but results depend on the individual CPU.

What to buy

  • Ryzen 3000 or 5000: a 3600 MT/s CL16 kit is the usual target. A 3600 CL18 kit is a reasonable budget option.
  • Intel 10th to 14th gen: 3200 CL16 or 3600 CL16 or CL18 are common choices. Intel 12th to 14th gen DDR4 boards typically stay stable at Gear 1 up to around 3600 to 3800 MT/s, but this varies by chip.
  • Capacity: two modules of 16 GB (32 GB total) is the recommended target for gaming. A 2×8 GB kit is the minimum.

Check your board’s memory support list before you buy. Not every board runs every XMP kit at its rated speed.

Why CL matters too

CL alone does not tell you how fast the first word of data arrives. Convert it to nanoseconds with CL × 2000 ÷ MT/s:

  • DDR4-3200 CL16 = 10 ns
  • DDR4-3600 CL18 = 10 ns
  • DDR4-3600 CL16 = 8.9 ns

A 3600 CL18 kit and a 3200 CL16 kit have the same first-word latency, but the 3600 kit has more bandwidth. For the full timing picture, see RAM timings and latency.

Turning on the speed you paid for

Most DDR4 kits start at a slower JEDEC default. Enable the XMP profile in your BIOS (called DOCP on some AMD boards) to run the rated speed. After you restart, check the speed in CPU-Z or your BIOS. If the system won’t boot at the XMP speed, lower the speed one step, or raise the DRAM voltage slightly within the kit’s specified range.

Is DDR4 still worth buying?

DDR4 is a legacy platform. Buy it when you already have an AM4 or Intel DDR4 board and want to keep it, or when you need a specific upgrade for that system. For a new build on a current platform, DDR5 is the normal choice (see DDR5 RAM speeds). DDR4 prices have moved over 2025 and 2026 as production has wound down, so compare current prices before you buy.

Common misconceptions

  • “DDR4-3200 runs at 3200 MHz.” It runs at 3200 MT/s, with a 1600 MHz clock.
  • “Faster is always better on Ryzen.” Beyond the FCLK limit, latency gets worse.
  • “The box speed is automatic.” XMP or DOCP must be enabled in the BIOS.
  • “Speed alone tells the whole story.” A 3600 CL18 kit and a 3200 CL16 kit have the same first-word latency.
  • “Any XMP kit will hit its rating on any board.” CPU memory controllers and board quality vary.

The complete guide to ram

PC RAM Guide: Module Types, Specs and How Much You Need
Read the guide

Keep exploring

Guides from other topics

All topics →