BIOS Settings

How to Enable Secure Boot in BIOS

Turn on Secure Boot in your UEFI BIOS: confirm UEFI mode, turn off CSM, set Secure Boot to Enabled, install default keys, and verify it in Windows.

On this page
  1. The short answer
  2. Check what your PC uses now
  3. Convert MBR to GPT if needed
  4. Turn off CSM
  5. Enable Secure Boot
  6. Save and verify
  7. When Secure Boot is greyed out or won’t stay on
  8. Secure Boot with Linux and GPU drivers
  9. Microsoft’s 2026 certificate change
  10. What Secure Boot does not do

Secure Boot checks that the software starting your PC is signed by a trusted party. It needs UEFI boot mode, the legacy CSM turned off, and a GPT system disk. Once those are in place, turning it on takes a few minutes in the BIOS.

The short answer

Confirm that Windows uses UEFI and that your disk is GPT. In the BIOS, turn off CSM, set OS Type to Windows UEFI, and set Secure Boot to Enabled. If the option is greyed out, install the default keys. Save with F10, then check Secure Boot State in Windows.

Check what your PC uses now

Press Windows + R, type msinfo32 and press Enter. Look at two lines:

  • BIOS Mode should say UEFI. If it says Legacy, your disk may be MBR and needs converting first.
  • Secure Boot State shows On or Off. If it already says On, you don’t need to change anything.

Convert MBR to GPT if needed

Turning off CSM on an MBR disk stops Windows from booting. Convert the disk to GPT first. Back up your data and suspend BitLocker before you start.

Open Command Prompt as administrator and run these commands. Check the disk number first. Disk 0 is the usual system disk.

mbr2gpt /validate /disk:0 /allowFullOS
mbr2gpt /convert /disk:0 /allowFullOS

Run the convert command only after validate reports success. Then move on to the BIOS.

Turn off CSM

In the BIOS, go to Boot and find CSM (Compatibility Support Module). On ASUS boards, set Launch CSM to Disabled. Other brands use similar names, and the menus vary by board.

Very old graphics cards may show no display with CSM off. If that happens, check that your GPU supports UEFI.

Enable Secure Boot

  1. Stay in Advanced Mode (F7 on ASUS) and go to the Boot or Security tab.
  2. Set OS Type to Windows UEFI Mode.
  3. Set Secure Boot to Enabled.

If the option is greyed out or the status says Setup Mode, the board has no keys installed. Go to Key Management and choose Install Default Secure Boot Keys. Secure Boot does not become active until the keys are loaded.

Other brands use different menus. On MSI, look under Settings > Security > Secure Boot. On Gigabyte, look under Boot > Secure Boot. On ASRock, look under Security > Secure Boot.

Save and verify

Press F10, confirm, and let the PC restart. Then open msinfo32 again and check that Secure Boot State says On. Resume BitLocker if you suspended it.

When Secure Boot is greyed out or won’t stay on

  • Check that UEFI mode is set and CSM is disabled. Secure Boot can’t be enabled under legacy boot.
  • Change Secure Boot Mode from Custom to Standard, or restore the factory keys. Names vary by board.
  • If the option is missing, update the BIOS. See how to update your motherboard BIOS.

Secure Boot with Linux and GPU drivers

Signed Linux distributions, such as Ubuntu, Fedora, Debian and openSUSE, boot with Secure Boot on. Some third-party drivers, including NVIDIA’s on Linux, may ask you to enroll a Machine Owner Key (MOK) on first boot. Follow the prompts from your distribution.

Microsoft’s 2026 certificate change

Microsoft’s original 2011 Secure Boot certificates began expiring in June 2026. Updated 2023 certificates are delivered through Windows Update and board firmware. Support depends on the board maker. Check your board’s support page and Windows Update before you assume your PC is covered.

What Secure Boot does not do

  • It is not the same as TPM. TPM is a separate setting, covered in how to enable TPM 2.0 in BIOS.
  • It doesn’t stop all malware. It protects the boot process only.
  • It does not slow down the PC or games.

For the rest of the settings to check after a build, see the BIOS settings guide. If you boot from a USB drive, how to change the boot order explains how Secure Boot can affect unsigned media.

The complete guide to bios settings

BIOS Settings Guide: How to Enter BIOS and What to Change
Read the guide

Keep exploring

Guides from other topics

All topics →