RGB Lighting

ARGB and RGB Headers: How to Connect PC Lighting

Learn the difference between 3-pin 5V ARGB and 4-pin 12V RGB motherboard headers, where each cable plugs in, and why the two should never be swapped.

On this page
  1. What is an RGB header on a motherboard?
  2. 12V RGB vs 5V ARGB at a glance
  3. Can I plug a 5V device into a 12V RGB header?
  4. Where to plug in a 3-pin ARGB cable
  5. Header names by brand
  6. How many devices fit on one header
  7. Running out of headers
  8. Safety before you connect

What is an RGB header on a motherboard?

An RGB header is a motherboard connector that powers LED lighting. Boards usually have two kinds, and they look similar, so check which one you have before you connect anything:

  • 12V RGB (4-pin): +12V, G, R and B. The whole strip or fan shows one colour at a time. Software can change that colour, but it can’t address each LED separately.
  • 5V ARGB (3-pin): +5V, Data and GND. The “A” means addressable. Each LED can show its own colour, which allows effects such as rainbows and chases.

12V RGB vs 5V ARGB at a glance

12V RGB (4-pin) 5V ARGB (3-pin)
Pins +12V, G, R, B +5V, Data, GND
Colour control One colour for the whole run Each LED can show a different colour
Typical effects Single colour, colour cycle Rainbow, chase, per-LED patterns
Common devices Many older RGB strips and fans Many current ARGB fans and strips

Can I plug a 5V device into a 12V RGB header?

No. Don’t do it. The two connectors are keyed differently, but a plug can still be forced or fitted offset onto the wrong header, and a 5V ARGB device on a 12V RGB header can be permanently damaged. If a plug won’t go in easily, don’t force it. Check the header label and the plug before you try again.

Where to plug in a 3-pin ARGB cable

  1. Shut the PC down and switch off the PSU.
  2. Find a header labelled ARGB or addressable. The label varies by brand (see the list below).
  3. Line up the arrow on the plug with the +5V pin. The connector has four positions with one pin missing, so it only fits one way.
  4. Push the plug fully home. A loose connection is a common reason for missing lights.

Many ARGB fans have two cables: a 4-pin PWM cable for fan speed and a 3-pin ARGB cable for lighting. The PWM cable controls speed only. The lighting comes from the ARGB cable, so both need to be connected for a fan to show both.

Header names by brand

Header names vary by board and revision, so check the silkscreen on your board and the manual. The guide to motherboard component names explains how the labels work.

  • ASUS: AURA RGB_HEADER (12V, 4-pin) and ADD_GEN2 (5V ARGB, 3-pin). Older boards have ADD_HEADER.
  • MSI: JRGB (12V, 4-pin) and JRAINBOW (5V ARGB, 3-pin). Some boards also have JCORSAIR for supported Corsair devices.
  • Gigabyte: LED_C (12V, 4-pin) and D_LED (5V ARGB, 3-pin).
  • ASRock: RGB_LED (12V, 4-pin) and ADDR_LED (5V ARGB, 3-pin). Some AMD boards also have an AMD_FAN_LED header for AMD Wraith coolers; see the Wraith cooler guide before using it.

Each brand’s software has its own guide: ASUS, MSI, Gigabyte and ASRock.

How many devices fit on one header

Each header has two limits: a current rating and a maximum LED count. Both are set by the board and vary from one model to another.

  • 12V RGB headers are often rated around 2A to 3A (24W to 36W), depending on the board.
  • 5V ARGB headers are usually rated around 3A (15W). Some Gigabyte boards quote 5A.
  • LED limits vary by vendor and board, from under 100 to around 1,000.

Read the wording carefully in your manual. Some manuals give one total for all of a board’s ARGB headers. Others give a limit per header. If the wording is unclear, assume the lower figure. For a worked example with fans, see how many ARGB lights you can daisy chain.

Running out of headers

Most boards have only a few lighting headers, so a full build can run out of them. There are a few ways to add more devices:

  • Powered hub: A hub connected to a SATA or Molex power connector from the PSU adds lighting power. Its data still comes from one motherboard header, so the header’s data connection is still a single point of control.
  • Splitter: A splitter divides one header’s connection across several cables. It does not add capacity, because every branch shares the header’s current limit.
  • Case or fan-kit controller: Many cases and fan kits include their own controller. Use it when the board has no spare header.

If devices don’t respond to the board software, the cause may be the controller rather than the header. The troubleshooting guide covers how to tell them apart.

Safety before you connect

  • Power off the PC and switch off the PSU before you connect or disconnect any lighting cable.
  • Check whether the header is 5V or 12V before you plug anything in.
  • Overloading a header can damage the motherboard. Spread devices across headers, or use a powered hub.

For mixed-brand setups, see syncing RGB across brands.

Keep exploring

Guides from other topics

All topics →