Short answer
A motherboard is made of a CPU socket, memory slots, expansion slots, storage connectors, power connectors, fan and front-panel headers, firmware chips, power regulators, and a rear I/O panel. Each part has a specific job, and the board’s manual labels all of them.
CPU socket and chipset
The CPU socket holds the processor. On Intel boards and on AMD AM5 boards, the pins are in the socket. On AMD AM4 boards, the pins are on the underside of the CPU. The socket is usually near the top centre of the board, and it is often the largest square part there.
The chipset handles extra PCIe lanes, USB, SATA and some storage. It sits lower on the board, usually under a heatsink. Modern CPUs handle memory and the main graphics link directly, so the chipset deals with the remaining connections.
VRM (voltage regulator module)
The VRM is a group of power stages, chokes and capacitors that steps down and steadies the power for the CPU. It sits near the socket, often under VRM heatsinks. More power stages can mean more headroom, but the count alone does not show that a board is well built.
Memory slots (DIMM)
The memory slots hold the RAM sticks. A board has two slots (common on Mini-ITX) or four (common on ATX and Micro-ATX). DDR4 and DDR5 use different keys, so a DDR4 stick will not fit a DDR5 slot.
Expansion slots (PCIe)
PCIe slots take expansion cards. The longest slot, x16, is for the graphics card. Shorter x1 and x4 slots take cards such as network, Wi-Fi, sound and capture cards. An x1 card fits in any slot size. A slot’s length does not always show how many lanes it uses. For more, see PCIe lane sharing.
M.2 slots
M.2 slots are small slots for SSDs. Most SSD slots use the M key. The E key is for Wi-Fi cards, which sit near the rear I/O panel on many boards. M.2 is a connector shape, so check the protocol and length before you buy a drive. For details, see how to know if an M.2 drive is compatible.
SATA ports
SATA ports are small, flat, L-shaped connectors for 2.5-inch SSDs, hard drives and optical drives. They carry data only. Drives get their power from a separate 15-pin power cable. More on this in what the SATA port looks like.
Power connectors
- 24-pin ATX connector. This is the main power input from the power supply. It sits along one edge of the board.
- 8-pin EPS connector (often 4+4). This powers the CPU. It is usually near the top-left of the board. Some high-end boards have a second one.
Fan and pump headers
Fan headers power and control the CPU cooler fan, case fans and AIO pump. Most are 4-pin PWM headers.
RGB and ARGB headers look similar but are not the same. RGB headers are 12 V and ARGB headers are usually 5 V. Plugging a 5 V ARGB device into a 12 V RGB header can damage it, so check the labels and the device’s spec before connecting.
Front-panel and USB headers
The front-panel header takes the case’s power and reset switches and its LEDs. It is usually at the bottom right of the board. See front panel power and reset connectors.
Other headers take the case’s front ports:
- USB 2.0 headers (9 pins, plus a key pin).
- USB 3.x headers (19 pins, plus a key pin).
- Front USB-C headers.
- HD audio headers for the front audio jack.
For the difference between the USB headers, see USB 2.0 vs USB 3.0 motherboard headers.
BIOS/UEFI chip and CMOS battery
The BIOS/UEFI chip stores the board’s firmware. It is a flash memory chip, and it is updated with a BIOS update.
The CMOS battery is a CR2032 coin cell. It keeps the clock and some settings running when the PC is off. It does not store the BIOS firmware.
Rear I/O panel
The rear I/O panel holds the USB ports, the wired network port, the audio jacks and any video outputs. Boards with built-in Wi-Fi also have antenna connectors here. See built-in vs add-in Wi-Fi.
How to find each part on your board
- The manual has a diagram of the board with each part labelled.
- The silkscreen labels printed on the board give names such as DIMM, PCIEX16, M2 and CPU_FAN. Label styles vary by brand.
- The product page lists the slots, headers and rear ports for the exact model.
For the buying order and the wider picture, see motherboard basics.