Short answer
Check that the CPU and board match, and that the board supports the CPU. Set the board on its box, line up the CPU’s triangle with the socket’s marker, lower the CPU straight in without pushing, then lock the lever. On LGA sockets (Intel and AM5), the pins are in the board, so never touch the socket. On AM4, the pins are on the CPU, so hold the chip only by its edges.
Before you start
- Check the CPU support list for your board. If the board needs a BIOS update before it will recognise your CPU, check whether it can update the BIOS without a CPU installed. Brands use different names for this, such as BIOS Flashback or Q-Flash Plus.
- Check the cooler. Confirm that it supports your socket. Many coolers include both Intel and AMD mounting kits.
- Gather what you need: a flat, non-conductive work surface (the board’s box works), the cooler, and thermal paste if the cooler does not come with it pre-applied.
- Install the CPU before the board goes in the case. It is much easier with the board flat on its box.
Ground yourself and handle with care
- Touch bare metal on the case or the power supply before you handle the CPU or the board.
- Hold the CPU by its edges. Do not touch the contacts on its underside.
- Keep the board on its box or an anti-static mat while you work.
Know your socket type
- LGA sockets (Intel LGA1700 and LGA1851, and AMD AM5) have flat contacts on the CPU. The pins are inside the socket on the board. Never touch them.
- AM4 (PGA) sockets have pins on the underside of the CPU. The socket has holes for them. Protect the CPU’s underside.
Install on an LGA socket
- Open the socket. Push the lever down and out to release it, then lift it to its full upright position. Raise the metal load plate.
- Align the CPU. Match the gold triangle on the CPU’s corner with the triangle marker on the socket. Intel CPUs also have notches that line up with tabs on the socket.
- Lower the CPU straight down. It should settle into the socket under its own weight. Do not push, slide or wiggle it.
- Close the load plate. Lower the plate, then press the lever back down and hook it under its retaining clip. Closing the lever takes firm pressure, and that is normal. The plastic socket cover usually pops off as the lever locks.
- Keep the socket cover. Some RMA processes require it, so store it with the board’s box.
Install on an AM4 socket
- Lift the lever to about 90 degrees.
- Align the CPU. Match the gold triangle on the CPU with the triangle on the socket.
- Drop the CPU in. It should sit flat with no force.
- Lower the lever to lock the CPU in place.
If an AM4 pin bends, it can often be straightened carefully. Bent pins on an LGA socket are much harder to fix, so take extra care there.
Mount the cooler and thermal paste
- Check for pre-applied paste. Many coolers come with paste already on the base. If yours does, do not add more.
- Apply paste if needed. A pea-sized dot or a small X is common. Good coverage and even mounting pressure matter more than the exact pattern.
- Follow the cooler’s instructions. Tighten the mounting screws gradually, in a cross pattern, so the pressure spreads evenly.
- Connect the fan to the CPU fan header.
Common mistakes
- Forcing the CPU. If it does not drop in, lift it out and check the alignment.
- Touching the pins. Keep your fingers off the socket pins and off the pins under an AM4 CPU.
- Mismatched alignment. The triangles must line up. A CPU in the wrong orientation will not sit flat.
- Too much paste. Excess paste can spread onto the board. Wipe off any spill.
- Losing the socket cover. Keep it with the board’s packaging.
If you are replacing an existing CPU
- Power off, unplug the power supply and remove the cooler. On AM4, warm the CPU slightly and twist the cooler gently to free it, so the CPU does not come out with it.
- Lift the lever, open the load plate and lift the old CPU out by its edges.
- Store the old CPU in an anti-static container, or put it back under its socket cover.
Common questions
Does the board need to be out of the case? It is easier to install the CPU with the board flat on its box. You can do it inside a case, but it is harder to see the alignment.
Is it normal for the lever to need force? Yes, on LGA sockets, closing the lever takes noticeable force. Forcing the CPU itself is not normal.
The PC won’t start after I install the CPU. Check the power cables and the memory seating first. A PC that will not start is often a wiring problem at the front-panel header, so see front panel power and reset connectors. If it still won’t start, see how to diagnose a DOA motherboard.
For the broader setup, read motherboard basics. After the install, you may need motherboard chipset drivers.