Motherboards

Front Panel Power and Reset Connectors: Where the Case Cables Go

Wire your case's power switch, reset button and LEDs to the front-panel header. Learn the usual pin layout, LED polarity and how to test before closing the case.

On this page
  1. Short answer
  2. What the cables do
  3. Where the header is
  4. The common pin layout
  5. Polarity: LEDs vs switches
  6. Connect, then test
  7. Common mistakes
  8. Q-Connector and similar blocks
  9. If the PC still will not start

Short answer

The front-panel header is a small block of pins near the bottom-right edge of the board. It is labelled F_PANEL, JFP1 or PANEL1, depending on the brand. The power and reset switches work either way round, but the LEDs need the correct polarity. Check the manual for the exact pins on your board.

What the cables do

  • Power switch (PWR_SW). Turns the PC on. This is the one cable you need to start the PC from the case.
  • Reset switch (RESET_SW). Restarts the PC. Some cases do not have one.
  • Power LED (PWR_LED+ and -). Lights when the PC is on.
  • Storage LED (HDD_LED+ and -). Flickers when a drive is active.
  • Speaker. A small speaker cable on some boards, used for beep codes.

Some cases use a single combined plug for several of these. Follow the case manual if your cables look different.

Where the header is

The header sits near the bottom-right edge on most boards. The label depends on the brand:

  • F_PANEL on many ASUS and Gigabyte boards.
  • JFP1 on many MSI boards.
  • PANEL1 on many ASRock boards.

The common pin layout

Many boards use a 2 × 5 block with one pin missing as a key. On the common Intel-style layout:

Pins Connects to
1 and 3 Storage LED (+ and -)
2 and 4 Power LED (+ and -)
5 and 7 Reset switch
6 and 8 Power switch
9 Unused, or reserved

Pin 10 is the missing key pin. Some boards add pins for other functions, such as a speaker or a chassis intrusion sensor. If your manual shows a different layout, follow the manual.

Polarity: LEDs vs switches

  • LEDs have polarity. The + wire is usually the coloured one, and the - wire is usually white or black. If an LED is reversed, it stays dark. No damage is done, so just turn it around.
  • Switches have no polarity. Either way round works.

Connect, then test

  1. Read the front-panel section of your board’s manual.
  2. Read the case manual. Many cases label each plug.
  3. Connect one cable at a time, and check each pin against the manual.
  4. Test before you close the case. With the power supply switched on and the board’s power connected, briefly touch the two power-switch pins with the tip of a metal screwdriver. The PC should start. Touch only those two pins. Shorting any other pins can damage the board.

Work on a non-conductive surface, keep your hands clear of the parts, and keep the screwdriver tip on the two pins only.

Common mistakes

  • Wrong header. Plugging the audio or USB cable into the front-panel block. Each has its own header.
  • Off by one pin. Check the pin count from the key pin.
  • Reversed LED. The LED stays dark. Turn the plug around.
  • Missing power-switch cable. A PC that will not start is often a power-switch cable on the wrong pins, not a dead power supply.

Q-Connector and similar blocks

Some boards have a small adapter block, such as ASUS’s Q-Connector. You plug the case cables into that block outside the board, then connect the block to the header. This is handy in tight builds.

If the PC still will not start

Check, in this order:

  1. The power-switch cable is on the power-switch pins.
  2. The power supply is switched on, and its 24-pin and CPU plugs are fully seated.
  3. The memory and CPU are seated correctly. See installing a CPU.

If none of these fixes it, work through how to diagnose a dead motherboard after a build.

For the other headers on the board, read USB 2.0 vs USB 3.0 motherboard headers. For the full list of named parts, see what the components on a motherboard are called.

The complete guide to motherboards

Motherboard Basics: Layout, Tiers and How to Choose
Read the guide

Keep exploring

Guides from other topics

All topics →