Motherboards

How to know if m2 is compatible with motherboard?

Check M.2 SSD compatibility in three steps: key (M or B+M), protocol (PCIe or SATA) and length. Find your board's M.2 specs and avoid buying the wrong drive.

On this page
  1. Short answer
  2. What M.2 is
  3. Check 1: the key
  4. Check 2: the protocol
  5. Check 3: the length
  6. Find your board’s M.2 specs
  7. Things that catch people out
  8. Buying checklist

Short answer

Check three things against your motherboard’s spec page: the key (M, or B+M), the protocol (PCIe/NVMe or SATA) and the length (such as 2280). If all three match a slot on your board, the drive should fit and work.

What M.2 is

M.2 is a connector shape and a form factor, not a speed. The same shape can carry SATA or PCIe signals. M.2 slots also take Wi-Fi and Bluetooth cards, which use a different key.

Check 1: the key

The key is the notch in the drive’s gold contacts and the matching shape in the slot. There are two common key positions, B and M.

  • M-key drives are PCIe NVMe SSDs. They fit M-key slots.
  • B+M drives are usually SATA SSDs. They fit both kinds of slot, but work only in a slot that supports SATA.
  • E-key slots are for Wi-Fi cards, which usually sit near the rear I/O panel. Do not put an SSD in an E-key slot.

If a drive will not go into a slot at all, the key is usually the cause.

Check 2: the protocol

  • PCIe (NVMe) is the faster option and is standard on current boards.
  • SATA runs at the same speed as a 2.5-inch SATA drive.
  • Some slots are PCIe-only and will not detect a SATA M.2 drive (see why Windows doesn’t see a new SSD). Some M-key slots support both, and the spec page says which.
  • A faster drive works in an older slot, but it runs at that slot’s speed.

Check 3: the length

M.2 sizes are written as a four or five-digit code. The first two digits are the width, which is 22 mm for each of these sizes. The rest is the length in millimetres. Common sizes are:

  • 2230 (30 mm)
  • 2242 (42 mm)
  • 2260 (60 mm)
  • 2280 (80 mm)
  • 22110 (110 mm)

Most desktop boards take a 2280 drive without trouble. Check the spec page for the lengths your slot supports. Each slot also has a standoff for one length, so use the standoff that matches your drive.

Find your board’s M.2 specs

  1. Identify the board. Open Windows System Information (msinfo32) and look for “BaseBoard Product”. You can also read the model printed on the board. How to find your motherboard model covers other ways.
  2. Search the manufacturer’s site for that exact model, and open the Specifications section.
  3. Find the M.2 slots. For each slot, note the key, the protocol, the supported lengths and the PCIe generation.
  4. Check the manual for shared resources. Some M.2 slots turn off SATA ports or reduce the graphics slot from x16 to x8. See PCIe lane sharing.

Things that catch people out

  • Lane sharing. An M.2 drive can take lanes from the graphics slot or from a SATA port.
  • NVMe boot. Booting from an NVMe drive needs UEFI support. Very old boards may not have it.
  • Heat. Newer PCIe 5.0 drives draw more power and often need a heatsink. Peel the protective film off any pre-applied heatsink pads.
  • Power. Power off and unplug the PC before you install a drive. M.2 drives are not designed to be swapped while the PC is on.

Buying checklist

  • Key: M, or B+M for SATA.
  • Protocol: PCIe (NVMe) or SATA, matching a slot on your board.
  • Length: a size your slot supports.
  • PCIe generation, if you want the speed of a newer drive.
  • A heatsink, if the drive needs one.

For the wider picture of slots and lanes, read PCIe lane sharing and expansion cards. For Wi-Fi in an E-key slot, read built-in vs add-in Wi-Fi.

The complete guide to motherboards

Motherboard Basics: Layout, Tiers and How to Choose
Read the guide

Keep exploring

Guides from other topics

All topics →