Motherboards

Motherboard Form Factors: ATX, Micro-ATX, Mini-ITX and E-ATX

Form factors set a motherboard's size and layout. Compare ATX, Micro-ATX, Mini-ITX and E-ATX, learn what EEB is, and check that your case fits before you buy.

On this page
  1. What a form factor is
  2. Common sizes at a glance
  3. ATX
  4. Micro-ATX
  5. Mini-ITX
  6. Micro-ATX vs Mini-ITX
  7. Can a Mini-ITX board fit an ATX case?
  8. E-ATX and EEB
  9. Check the case before you buy the board
  10. Quick checklist

What a form factor is

A motherboard form factor is the standard that sets a board’s size, the positions of its mounting holes, the power connector layout and the rear I/O panel. Boards of the same form factor fit the same kinds of cases, so the form factor is the first thing to check against your case.

Common sizes at a glance

Form factor Typical size Typical expansion slots Best for
ATX 305 × 244 mm (12 × 9.6 in) Up to 7 Full-size desktops with the most room
Micro-ATX Up to 244 × 244 mm (9.6 × 9.6 in) Up to 4 A balance of size, features and price
Mini-ITX 170 × 170 mm (6.7 × 6.7 in) 1 Compact and small-form-factor builds
E-ATX Commonly about 305 × 330 mm (12 × 13 in) Varies High-end and workstation builds
SSI EEB 305 × 330 mm Varies Servers and workstations

Slot counts are typical maximums. Check the board’s spec page for the real number.

ATX

ATX is the standard full-size desktop board. It arrived in 1995 and replaced the older AT and Baby AT layouts. ATX boards have the most room for memory slots, PCIe slots, M.2 slots and cooling. They need a full-size case.

Micro-ATX

Micro-ATX boards are smaller than ATX and fit many mid-tower cases. They are often the least expensive option for a given chipset.

Is there a downside to Micro-ATX?

There are a few trade-offs. A Micro-ATX board has fewer expansion slots, sometimes fewer M.2 slots, and less room for large heatsinks. Smaller boards are not inherently slower. Board size alone does not decide performance, so compare the specific board’s power delivery, cooling and features rather than assuming a Micro-ATX board is weaker.

On AM4 and AM5 boards, an “M” after the chipset name means Micro-ATX. You will see names such as A620M, B650M, B850M and B550M. For more on reading names, see motherboard model names.

What is the best Micro-ATX AM4 board?

There is no single best board. Compare the chipset tier, the number and PCIe generation of the M.2 slots, the rear ports, the VRM cooling, and whether the BIOS supports the CPU you plan to use. Then read recent reviews of the specific boards you are considering.

Mini-ITX

Mini-ITX boards measure 170 × 170 mm, which makes them the smallest of these sizes. They usually have one PCIe slot, which is normally used for the graphics card, and two memory slots. Many have one or two M.2 slots, and some put one on the back of the board.

Mini-ITX boards often cost more than Micro-ATX boards because the layout is tight. They also leave less room for cable routing and cooling, so plan the build carefully.

Micro-ATX vs Mini-ITX

These are different standards, not interchangeable names. Mini-ITX is the smaller of the two.

  • Choose Micro-ATX if you want more slots, a lower price and an easier build.
  • Choose Mini-ITX if desk space or portability matters most, and you accept fewer slots and memory options.

Can a Mini-ITX board fit an ATX case?

In most cases, yes. ATX cases accept smaller boards, so a Mini-ITX board can usually be mounted in an ATX case. Check that the case’s mounting holes line up with the board’s holes, and check the case’s supported board sizes.

E-ATX and EEB

E-ATX boards are larger than ATX. The name is not one fixed size. Commonly, E-ATX boards measure about 305 × 330 mm, but widths vary from board to board, so check your case’s listed maximum board width before you buy.

EEB (SSI EEB) is a server and workstation standard. It is about 305 × 330 mm and has its own mounting hole pattern. It is not the same as E-ATX, and not every E-ATX case has the holes an EEB board needs. Most home builders will not need EEB. If you do, confirm the dimensions and hole pattern on the spec sheet first.

Check the case before you buy the board

  • Supported board sizes. Look for ATX, Micro-ATX, Mini-ITX and, if you need it, E-ATX or EEB.
  • Mounting holes. The standoffs in the case must match the board’s holes. A standoff that sits under the board where there is no hole can short the board, so remove any that do not line up.
  • Graphics card length and cooler height. Check the case’s listed maximum GPU length and CPU cooler height. The PC cooling guide compares air and liquid coolers.

Quick checklist

  • The case lists the board’s form factor.
  • The standoffs match the board’s holes.
  • The graphics card and cooler fit.
  • The board has the M.2, SATA and PCIe slots you need.

For the rest of the buying order, see motherboard basics. If you plan to use a board with rear connectors, read about back-connect motherboards, which are mostly ATX and Micro-ATX.

The complete guide to motherboards

Motherboard Basics: Layout, Tiers and How to Choose
Read the guide

Keep exploring

Guides from other topics

All topics →