Motherboards

PCIe Lane Sharing and Expansion Cards

Adding an M.2 drive can cut your GPU to x8 or disable a SATA port. Learn how lane sharing works, how to check your manual and how to fit a PCIe card.

On this page
  1. Short answer
  2. What a PCIe lane is
  3. Where lanes come from
  4. What lane sharing looks like
  5. Does x8 hurt performance?
  6. How to check your board
  7. Plan your slots
  8. Install a PCIe card
  9. Find the adapter in Windows
  10. Common questions
  11. SATA add-in cards

Short answer

Lane sharing means two slots or ports draw on the same set of PCIe lanes. Adding a device in one place can slow down or disable another. Check the motherboard manual before you add an M.2 drive or a card, and plan your slots before you build.

What a PCIe lane is

A lane is a pair of data paths between a device and the rest of the system. Slots are described by the number of lanes they can use: x1, x4, x8 or x16.

A slot’s physical length does not tell you how many lanes it is wired for. A full-length slot can be wired for x4 or x8, so check the manual for the real number.

Where lanes come from

  • CPU lanes usually serve the main graphics slot and the first, fastest M.2 slots. They are direct and have low latency.
  • Chipset lanes serve extra M.2 slots, USB, networking, SATA and secondary slots. They share a single link back to the CPU.

What lane sharing looks like

  • The graphics card drops from x16 to x8 when a specific M.2 slot is in use.
  • An M.2 drive disables one or two SATA ports.
  • A second PCIe slot is disabled when another slot or M.2 connector is used.
  • On some X870 and X870E boards, certain USB4 ports share lanes with an M.2 slot.

The board decides these rules. There is no universal rule based on slot number or position, and two boards with the same chipset can route their lanes differently.

Does x8 hurt performance?

Often by very little. Most current graphics cards show only a small difference at x8 on PCIe 4.0. Older PCIe generations, cards with fewer lanes and data-heavy workloads can be more sensitive. The impact depends on the card, the game, the resolution and the workload. For the other checks, see graphics card and motherboard compatibility.

How to check your board

  1. Find your exact model and revision on the manufacturer’s site, and download its manual.
  2. Read the expansion-slot and storage sections. Look for notes such as “shares bandwidth”, “operates at x8” or “disabled when”.
  3. Check the block diagram or the bifurcation table. It shows which slots connect to the CPU and which connect to the chipset.
  4. Check the CPU restrictions. Some boards change which slots work with certain CPUs.
  5. After you install a device, confirm it appears in the BIOS or in Windows. To check the active link width under load, use a monitoring tool.

If the manual is unclear, use the board maker’s support material for that exact model. Two boards with the same chipset can route lanes differently.

Plan your slots

  1. Put the graphics card in the main x16 slot, which is usually the top one.
  2. Put your primary NVMe drive in the M.2 slot that connects to the CPU.
  3. Put secondary storage and expansion cards where the manual’s sharing table allows.

If you are choosing a board, count the M.2 drives, cards and high-speed ports you expect to use over the life of the PC. For the slot count of each size, see motherboard form factors.

Install a PCIe card

Before you start: download the card’s drivers, such as Ethernet, Wi-Fi or Bluetooth drivers, on another device if you can. Some installs drop the network until the driver is in place. For a slim desktop, fit a low-profile bracket to the card first.

  1. Power down. Turn the PC off, unplug the power supply, and touch bare metal on the case to discharge static.
  2. Open the case. Remove the side panel.
  3. Remove the slot cover. Pick an open slot and remove the metal cover opposite it. Keep the screw.
  4. Hold the card by its bracket or edges. Avoid touching the gold contacts.
  5. Seat the card. Line up the card’s notch with the key in the slot. Press straight down, firmly and evenly, until the card sits fully in the slot.
  6. Secure the bracket with the screw or the case latch.
  7. Connect any extra cables. A Wi-Fi card’s Bluetooth cable, for example, goes to an internal USB 2.0 header.
  8. Attach the antennas. Signal is very weak without them.
  9. Reassemble, power on, and install the drivers. Test the connection.

A x1 card fits in an x1, x4, x8 or x16 slot. A 2.5 GbE network card, such as those using an Intel I226 or Realtek RTL8125 chip, needs an x1 slot. A 10 GbE card usually needs an x4 link.

Find the adapter in Windows

Open Device Manager and expand Network adapters. It lists the Ethernet or wireless adapter. A yellow exclamation mark means the driver is missing.

Common questions

What is PCIe on an SSD? A PCIe SSD is a solid-state drive that connects over PCIe lanes, usually through an M.2 slot, and uses the NVMe protocol. It is much faster than a SATA SSD. The drive’s key and length must match the slot. See how to know if an M.2 drive is compatible.

Can you put a Wi-Fi card in a PCIe slot? Yes. Many Wi-Fi cards use a PCIe x1 slot. Check that you have a free slot, and room for the antennas. For more, see built-in vs add-in Wi-Fi.

Can I connect PCIe to a GPU? A graphics card goes straight into a PCIe x16 slot on the board. You do not connect it through a separate PCIe connection. Riser cables can mount a card away from the board, but they are a specialist setup and need care.

Can an M.2 SSD disable a SATA port? Yes, on some boards. The manual lists which SATA ports are disabled and when. See what a SATA port looks like.

Is bifurcation the same as lane sharing? They are related but not the same. Bifurcation splits one group of lanes into smaller links, such as x16 into x8 and x8. Lane sharing is when two devices depend on the same limited set of lanes.

Does every M.2 slot take GPU lanes? No. Some M.2 slots connect to the CPU, some connect to the chipset, and some share lanes with the graphics slot. Check the manual for each slot.

SATA add-in cards

A PCIe SATA card adds ports to the board. Many use controllers such as the ASMedia ASM1166 (6 ports) or the JMicron JMB585 (5 ports), which typically need an x2 link. Check the card’s link width and whether it uses a port multiplier before you buy.

For the basics of the motherboard’s built-in SATA ports, see what a SATA port looks like. For the overall buying order, see motherboard basics.

The complete guide to motherboards

Motherboard Basics: Layout, Tiers and How to Choose
Read the guide

Keep exploring

Guides from other topics

All topics →