RGB Lighting

How many argb lights can I daisy chain?

How many ARGB fans or lights you can daisy chain on one header, why LED count and header amperage matter more than fan count, and when to use a hub.

On this page
  1. Quick answer: count LEDs and amps, not fans
  2. Why fan count is the wrong measure
  3. Two limits: header current and LED count
  4. Work out the load for your chain
  5. Read the manual’s wording
  6. Splitters and hubs
  7. Mixing brands
  8. Long chains: flicker and colour shift
  9. Signs of overload
  10. Safety

Quick answer: count LEDs and amps, not fans

A common rule of thumb is 3 to 6 ARGB fans on one 5V header. Treat that as a starting point, not a limit. The real limit comes from your board’s current rating and the total LED count in the chain, so work those out before you count fans.

Why fan count is the wrong measure

Fans differ widely. A typical ARGB fan has 8 to 20 LEDs, and some ring fans have 30 or more. A strip can have 30 to 60 LEDs per metre. Two fans with 30 LEDs each draw more than two fans with 8 LEDs each, even though the fan count is the same.

Two limits: header current and LED count

Each 5V ARGB header has two limits:

  • A current rating, usually 3A (15W) at 5V. Some Gigabyte boards quote 5A.
  • A maximum LED count that the header’s controller supports. This varies by vendor and board, from under 100 to around 1,000.

A chain can exceed either limit, and exceeding one is enough to cause problems.

Work out the load for your chain

The worst case is full white. A WS2812B-type LED can draw up to about 60mA at full white, and about 20mA when showing a single colour. At those values:

  • 3A ÷ 60mA ≈ 50 LEDs at full white.
  • 3A ÷ 20mA ≈ 150 LEDs in a single colour.

To work out your own load:

  1. Count the LEDs on every device in the chain.
  2. For each device, use the manufacturer’s current rating if it has one. Otherwise, estimate up to 60mA per LED at full white.
  3. Add the totals and compare them with your header’s current rating and LED limit in the manual.
  4. Leave headroom. LEDs and fans can draw more current at full white or during startup.

Real effects rarely stay at full white for long, so the full-white figure is a conservative plan rather than a typical reading.

Read the manual’s wording

Manuals don’t always use the same wording. Some list one total for all of the board’s ARGB headers. Others list a limit per header. If the wording is unclear, assume the lower figure, or ask the board’s vendor. Don’t assume a per-header figure applies to every header on the board.

Splitters and hubs

A splitter divides one header’s connection across several cables. It doesn’t add capacity, because every branch shares the header’s current limit.

A powered hub is different. It connects to a SATA or Molex power connector from the PSU, which supplies the lighting current. The data still comes from one motherboard header, so a hub adds current but not a second data source.

If your total is over the header’s limit, use a powered hub. Keep each hub within its own rating too.

Mixing brands

Standard 3-pin ARGB devices chain together. Some proprietary connectors, such as those from Corsair and Lian Li, may not chain with standard ARGB. Use an adapter designed for the device, or the brand’s own controller. For the options, see syncing RGB across brands.

Long chains: flicker and colour shift

Long chains can cause two kinds of problem:

  • Data problems: a long or poorly connected chain can cause flicker or wrong colours toward the far end.
  • Voltage drop: over a long run, the far LEDs can dim or shift toward red or orange.

To fix either, shorten the run, use a powered hub, or split the devices across headers.

Signs of overload

If you see these, power off and remove devices until the chain is stable. Then check the header’s rating and recount the load. For more on fixing lighting faults, see the RGB troubleshooting guide.

Safety

  • Overloading a header can damage the motherboard. Spread devices across headers, or use a powered hub.
  • Power off and switch off the PSU before you change the chain.
  • Never connect a 5V ARGB chain to a 12V RGB header.

For the header types and their labels, see ARGB and RGB headers. For ASUS boards, the LED count on Gen 1 headers must match the chain. See how to control RGB on an ASUS motherboard.

The complete guide to rgb lighting

ARGB and RGB Headers: How to Connect PC Lighting
Read the guide

Keep exploring

Guides from other topics

All topics →