A PC that turns on and then shuts off almost at once is usually protecting itself. Something has tripped a safety cutoff, a short circuit or an overheating check. Most causes can be found with a few checks and a minimal boot. Work through them in order, and power off before you touch anything inside the case.
Safety first
- Switch off the PSU and unplug the power cord before you open the case.
- Never open a PSU. Its capacitors can hold a dangerous charge after unplugging.
- Unplug at the wall before you check standoffs or cables.
Use the timing as a clue
How quickly the PC shuts off can point to the likely cause.
- A shutoff within about a second often points to a protection trip, a short circuit or an over-current event. Check for shorts and power cabling first.
- A shutoff after several seconds can point to the CPU overheating. Check the cooler contact, the pump and the fan headers.
- A PSU fan that twitches and then stops suggests the PSU’s protection has tripped.
- A few restarts before it runs can be normal. DDR5 memory training can power-cycle the PC several times on the first boot. Many boards also restart once or twice after a CMOS clear or a RAM settings change.
Check the power connections
- Reseat the 24-pin motherboard cable, the CPU power cable (8-pin EPS), and every GPU power connector, at both the board or card and the PSU.
- Make sure the PSU’s switch is on. On older PSUs with a voltage selector, check that it matches your mains voltage.
- While testing, plug the PC straight into a wall outlet instead of a power strip or surge protector.
If the 8-pin EPS cable isn’t connected, many boards won’t start with the fans running. Some boards power off instead, so check it even if the PC seems to start.
Look for shorts
Shorts are a common cause, and they’re often easy to fix.
- Remove any extra or misplaced standoffs, and check that every standoff lines up with a mounting hole.
- Check for loose screws or stray cables behind the motherboard tray.
- Make sure the board isn’t touching the case.
- Disconnect the front-panel USB and audio headers, drives and USB devices while you test.
- Check the front-panel wiring. A reset switch wired to the power pins, or a stuck power button, can cause on-off behavior.
Check the CPU cooler
Overheating can switch a PC off after a few seconds.
- Make sure the cooler is mounted firmly and plugged into the correct fan or pump header.
- Remove the protective plastic film from the cooler’s base if it’s still there.
- For an all-in-one liquid cooler, make sure the pump has power.
- Tighten the cooler evenly. An over-tightened cooler or bent socket pins can cause restart loops.
- Check your CPU’s rated maximum temperature in its specification. Don’t guess at it.
Check RAM and memory settings
- Reseat each RAM stick until the clips lock.
- Test one stick in the slot the manual recommends, then try each stick in turn.
- If the failures started after you enabled XMP or EXPO, turn it off. An unstable memory profile can cause restart loops.
Run a minimal boot
A minimal boot removes everything the PC doesn’t need to start.
- Remove all drives, USB devices and extra cards.
- Keep the CPU, cooler, one RAM stick, the motherboard and the PSU connected. Keep the GPU only if the CPU has no integrated graphics.
- Start the PC.
If it stays on, add one part back at a time until it shuts off. The last part you added is the likely cause. If it still shuts off with the minimal setup, test with a known-good PSU.
Clear CMOS
A CMOS clear resets BIOS settings, including any bad memory or overclock settings. Unplug the PSU, then use the CMOS button or jumper, or remove the CR2032 battery for a few minutes. Put the battery back and try again.
Common misconceptions
- A PSU that powers on isn’t necessarily healthy.
- A few restarts on the first DDR5 boot aren’t a fault.
- Shorts and cooling problems are often more likely causes than the motherboard.
When to suspect the board or PSU
If the minimal setup still shuts off, there are no shorts, the cooler is making good contact, and a known-good PSU changes nothing, the board may be faulty. The DOA diagnosis guide covers the next steps.
If the PC restarts into a startup code, the ASUS code 15 guide and the motherboard debug codes guide can help narrow it down. If the message mentions Anti-Surge, read the ASUS Anti-Surge guide.