After a graphics card install, a black screen is most often caused by a cable, card seating, power or a BIOS display setting. A dead card is less likely. Work through the checks below in order, starting with the quickest.
Check the monitor cable and port
- Plug into the graphics card. The most common cause is a monitor plugged into the motherboard’s video port instead of the GPU. Use the card’s ports.
- Try another cable or port. Swap the cable, or try a different port on the card.
- Check the monitor’s input. Set the monitor to the input you’re actually using. On the wrong input it will show “no signal.” Try HDMI instead of DisplayPort, or the reverse.
Seat the card and check power
- Power off, unplug the PSU, and press the power button once to drain residual power.
- Seat the card fully in the top x16 PCIe slot, until the latch clicks.
- Connect every power connector on the card. Many cards won’t output video unless all of their power connectors are plugged in.
- For high-power cards, use a separate PCIe cable for each connector, not a daisy-chained cable. Your PSU’s manual has its own guidance.
- Check that your PSU meets the card maker’s recommended wattage.
- For a 12VHPWR or 12V-2x6 plug, push it in until it’s fully seated with no gap. Avoid sharp bends right at the plug.
Test with the motherboard’s video output
If your CPU has integrated graphics, plug the monitor into the motherboard’s video port and see what happens.
- You get a picture. The display and the board are fine. The card or its setup is the likely problem, so check seating, power and the BIOS display setting.
- You get no picture from either port. Look at the RAM, the CPU and the board’s startup codes. A VGA debug light that stays on means the board can’t start a graphics device. The motherboard debug codes guide explains the lights.
Check the BIOS display settings
- Primary display. Many boards turn off the integrated graphics when a graphics card is installed. Look for a “Primary Display” or similar setting, and set it to PCIe if needed.
- CSM and Resizable BAR. Very old cards, roughly pre-2012, may need the Compatibility Support Module (CSM) enabled. Resizable BAR generally needs CSM disabled. Change one setting at a time, and note the defaults so you can go back.
- BIOS and firmware updates. Some newer GPUs need a motherboard BIOS update or a GPU firmware update to fix black screens. Check the support pages for your board and your card.
Driver problems
If the picture appears in the BIOS but the screen goes black when Windows loads, the driver is the likely cause.
- Boot using the integrated graphics or in Safe Mode.
- Run Display Driver Uninstaller (DDU) in Safe Mode to remove the old driver. Download DDU from its developer’s site.
- Install the latest driver for your card.
Test the card
If the card works in another PCIe slot or another PC, the original slot or setup is the problem. If it fails everywhere, the card may be faulty. Use your previous graphics card to compare, if you have one.
If you use a riser cable or a vertical mount, the riser can cause black screens. In the BIOS, try setting the slot to PCIe Gen 3 or Gen 4 instead of Gen 5.
Common misconceptions
- GPU fans spinning doesn’t prove the card is outputting video.
- A no-display problem is usually cabling or seating, not a dead GPU.
- A bigger PSU won’t fix a loose power cable.
Information to share when you ask for help
If you still need help, share these details: your motherboard model, CPU, GPU model and PSU wattage. Also say whether the fans and RGB lights turn on, whether the motherboard’s debug lights are lit, and whether you get a picture from the motherboard’s video output.
If the PC switches off instead of showing a black screen, see PC turns on and shuts off immediately. If you get no picture at all after every check, see the DOA diagnosis guide.
Safety
- Power off and unplug before you reseat the card or any cable.
- Stop using a 12VHPWR plug that shows melting or discoloration.
- Handle the card with basic static precautions. The anti-static mat guide covers them.