Build Troubleshooting

Motherboard Debug LEDs and Q-Codes Explained

Learn what the four debug LEDs and Q-code displays on a motherboard mean, how to read ASUS codes like AA and A0, and whether you need debug LEDs.

On this page
  1. Debug LEDs: the four lights
  2. Q-code displays
  3. Common codes and what they often mean
  4. Do you need a board with debug LEDs?
  5. Resetting an ASUS board and finding the model
  6. Common misconceptions
  7. When a code sticks

Debug LEDs and Q-code displays show how far startup has got. They help you find the stage where a board stops. Codes differ between brands and BIOS versions, though, so read them as a pointer rather than a verdict.

Debug LEDs: the four lights

Many motherboards have four debug lights, usually labeled CPU, DRAM, VGA and BOOT. Brands use their own names for them. ASUS calls them Q-LEDs, MSI calls them EZ Debug LED, and Gigabyte calls them Status LEDs.

The lights come on in the order that startup runs. A light that stays on marks where startup stopped.

Light that stays on Often means First thing to check
CPU The processor isn’t starting CPU seating and the 8-pin EPS power
DRAM Memory is still being set up, or has a problem RAM seating, and one stick in the manual’s slot
VGA No graphics device found Monitor cable and GPU seating
BOOT No bootable drive found Drive connections and boot order

A light that flashes briefly on every boot is normal. Only a light that stays on matters. A DRAM light can stay on for several minutes during DDR5 memory training, which is also normal.

Q-code displays

Higher-end boards often have a two-digit display that shows hexadecimal codes. ASUS ROG, MSI MEG and Gigabyte Aorus boards are examples. Many AM5 boards use debug LEDs instead, and Q-code displays are less common.

Codes flash by during every normal boot. Only a code that stays on the display matters.

The codes are based on AMI Aptio POST codes, but each vendor customizes them. Use the table in your board’s manual rather than a list from a forum.

Common codes and what they often mean

The table below lists common examples. Meanings vary by brand and BIOS, so check your manual before you act on any of them.

Code Often means Where to look
00 The CPU isn’t detected or initialized CPU seating and EPS power
15 Early memory setup has started Code 15 guide
53 Memory error, such as an invalid type or speed RAM type, speed and seating
55 Memory not installed or not detected RAM seating and slots
99 Super I/O setup, sometimes tied to a USB or PCIe device Unplug extra devices and retest
D6 No console output device, usually a GPU or display Monitor cable and GPU
A0 The “booted” code on many Intel boards Nothing, if the PC runs normally
AA On ASUS, POST has finished and the OS is taking over Nothing, if the PC runs normally

AA and A0 are not errors

On an ASUS board, AA usually means POST has finished and the system is handing control to the operating system. If the PC runs normally with AA showing, you can ignore it.

If the PC freezes on AA and never reaches Windows, look at the monitor input, the boot drive and the OS boot loader. A missing display or a failure to reach Windows usually points to those, not to a failed board.

A0 varies by board and BIOS, so check your manual before reading it as an error.

Do you need a board with debug LEDs?

Debug LEDs are useful, not essential. Many AM5 boards, including B650, X670, B850 and X870 models, have them. Q-code displays are less common and usually appear on higher-end boards.

Beep codes are another diagnostic, but they need a speaker on the board, and many boards don’t have one. Don’t rely on beeps.

A board without debug lights can still be diagnosed with the manual, a minimal boot and the steps in the troubleshooting guides. For a board that won’t start at all, see the DOA diagnosis guide.

Resetting an ASUS board and finding the model

People who ask how to reset an ASUS motherboard usually mean resetting the BIOS settings, which is a CMOS clear. Use the CMOS clear button or jumper described in the manual. Or power off, unplug the PSU, and remove the CR2032 battery for several minutes, then put it back.

To check the board model, read the model name printed on the board itself. BIOS screens differ between versions, so the printed label is the most reliable source.

Common misconceptions

  • Q-codes aren’t universal. Meanings differ between Intel and AMD boards and across brands.
  • AA and A0 are not errors.
  • A lit DRAM light during DDR5 training is normal for several minutes.
  • A code points to a stage, not to a confirmed bad part.

When a code sticks

  1. Read the exact meaning in your board’s manual.
  2. Power off, unplug the PSU, and reseat the RAM and the CPU power connector.
  3. Clear CMOS, then check whether the code changes.
  4. If the code is 99 or similar, unplug extra USB and PCIe devices and retest.
  5. If the PC restarts instead of sticking on a code, see PC turns on and shuts off immediately.

Always power off and unplug the PSU before you reseat RAM or the CPU.

The complete guide to build troubleshooting

Dead Motherboard After a Build? How to Diagnose a DOA Board
Read the guide

Keep exploring

Guides from other topics

All topics →