An AIO install usually takes 30 to 60 minutes once the parts are laid out. The order matters: check the fit first, mount the hardware and radiator, place the pump on the CPU, then connect the cables and check the results in BIOS. This guide follows that order and points out the mistakes that cause the most trouble.
Check fit before you open the box
Confirm three things before you start:
- Socket support: the kit must list your CPU socket, such as LGA1700, LGA1851, AM4 or AM5.
- Radiator fit: check that your case takes the radiator size and thickness, including the fans.
- Top clearance: a radiator of about 27 mm plus fans of about 25 mm adds up to roughly 52 mm. Check that figure against your RAM and any tall motherboard heatsinks.
Pick the radiator position
A top exhaust mount is the usual best choice, because heat rises out of the case. A front mount also works, with the tubes arranged so the pump isn’t the highest point.
Two rules apply to any position:
- The pump must never be the highest point of the loop. Air collects at the highest point.
- Fans can blow out the side, toward the frame struts or label, depending on the cooler’s design. Check the orientation in the manual.
For the fit and placement questions in one place, see the PC cooling guide.
Install the mounting hardware
The steps differ for AMD and Intel.
- AMD: remove the stock plastic retention clips from the motherboard. Many AIOs reuse AMD’s stock backplate, but this varies, so check the kit.
- Intel: install the backplate behind the motherboard and screw in the standoffs for your socket.
If the case blocks access to the back of the board later, install the backplate before you mount the motherboard. Otherwise, you can mount the radiator and fans first.
Mount the radiator and fans
- Attach the fans to the radiator using the longer screws that come with the kit.
- Mount the radiator to the case with the shorter radiator screws.
- Use only the screws supplied with the kit. Longer screws can puncture the radiator.
Route the fan cables toward the back of the case, so they stay clear of the blades.
Install the pump on the CPU
- Peel the protective cover off the cold plate.
- Check whether the cold plate has pre-applied thermal paste. Most AIOs do. If it does, don’t add more.
- If there’s no pre-applied paste, apply the amount and pattern your cooler’s manual gives.
- Set the pump block evenly on the CPU.
- Tighten the pump block screws diagonally, a few turns at a time, until they stop.
For a fuller guide to paste, see how to replace thermal paste on your CPU.
Connect the cables
- Pump: connect it to the motherboard’s AIO_PUMP header, or to CPU_FAN if your board requires it. Set the pump to full speed or the speed the maker recommends.
- Radiator fans: connect them to CPU_FAN, CPU_OPT or the AIO’s fan hub, depending on the kit.
- Extras: some AIOs need a USB 2.0 header, a SATA power connector or a 5 V ARGB header for lighting, display or software control. Connect only what your kit requires.
- Tubes: route them without kinks. Keep them clear of fans and the graphics card.
For how headers work and why 3-pin devices behave differently, see 3-pin CPU fan on a 4-pin motherboard.
First boot: check pump speed and temperatures
After the first boot, go into the BIOS and check:
- the pump’s reported speed, to confirm it’s spinning
- the fans’ reported speeds
- the idle CPU temperature, which often sits around 30 to 40 °C, though this varies with room temperature and the cooler
If the pump isn’t spinning, power off and check the header connection. If it’s gurgling after the first boot, that’s usually air in the loop. See AIO pump noise.
Common mistakes
- Assuming a front-mounted radiator always performs badly. It can work well. Pump position and airflow decide the result more than the mounting spot.
- Adding extra paste on pre-applied paste. It spreads over the edges and doesn’t help.
- Setting the pump to a fan curve that can drop to zero. A stopped pump can overheat the CPU. Keep the pump at a fixed speed.
- Believing the tubes must always point up. What matters is that the pump isn’t the highest point.
Safety
- Power off, switch off the PSU and unplug the PC before you start.
- Touch bare case metal before handling parts, to discharge any static.
- Never open the AIO pump or its tubing.
For the fan and pump settings after install, see how to set a fan curve.