Positive pressure means you push more air into the case than you pull out, so air leaks out through the gaps and less unfiltered dust gets in. Negative pressure means you pull more air out, so air and dust are drawn in through every unfiltered gap. Temperature differences between the two are usually small. Total airflow and the air path through the case matter more than the label.
What case pressure means
Case pressure depends on the balance between intake and exhaust fans:
- Positive pressure: intake airflow is greater than exhaust airflow.
- Negative pressure: exhaust airflow is greater than intake airflow.
- Balanced: intake and exhaust are about equal.
The balance is about what the fans actually move, not how many fans you have. Filters, radiators and solid front panels all reduce intake airflow.
Positive pressure
Positive pressure is the common choice for people who want less dust. Air leaks out through gaps in the case, so fewer dust particles come in through unfiltered openings. The trade-off is that you must filter every intake and clean the filters. A clogged filter cuts the intake, and then the balance tips toward negative.
A common positive setup is two or three front intakes, one rear exhaust and an optional top exhaust.
Negative pressure
Negative pressure pulls air through every gap, so unfiltered openings become dust entry points. It can make a case feel more open, and it’s sometimes used when the case has strong exhaust needs. It doesn’t run hotter by default. Temperatures depend on the total airflow and the path it takes.
Balanced airflow
Balanced airflow sits between the two. Intake and exhaust move about the same amount of air. It’s a reasonable target if you want both moderate dust control and good temperatures, though the exact result depends on the case.
Count airflow, not fans
A 120 mm fan is typically rated somewhere around 40 to 80 CFM. Those ratings are free-air figures, measured without restriction, so the real numbers in a case are usually lower. Filters, radiators and a solid front panel all restrict the intake. Two intakes behind a dense mesh front can move less air than one intake behind an open mesh.
For this reason, judge the setup by its real temperatures and noise, not by counting fans.
Where the radiator and GPU fit in
A radiator changes the airflow balance. A front-mounted radiator used as an intake pulls air through the radiator, and that air can be warmer when it reaches the case interior, which can raise GPU temperatures by a few degrees. A top-mounted radiator used as an exhaust tends to keep the case air cooler, because the hot air leaves the case.
Open-air graphics card coolers dump heat into the case, so an exhaust above and behind the GPU helps. A bottom intake helps feed the GPU as well.
A common setup to start from
A reasonable starting layout is:
- two to three front intakes, with filters
- one rear exhaust
- an optional top exhaust, which keeps the balance slightly positive
- a bottom intake, if the case has room, to feed the GPU
Adjust from there based on your temperatures. The PC cooling guide covers default airflow in more detail.
How to test your own case
You can test airflow with simple tools:
- Hold a smoke pen, incense stick or a tissue near the gaps in the case. Smoke that pulls inward shows negative pressure at that spot. Smoke that pushes outward shows positive pressure.
- Run a 15 to 30 minute load and record CPU and GPU temperatures in HWiNFO. Repeat the test for each fan configuration you try, under the same load.
- Note the noise level as well, because a setup that’s a few degrees cooler but much louder may not be the better choice.
Filter and maintenance schedule
Clean intake filters every one to three months. The right interval depends on your environment. A home with pets or a dusty room needs cleaning more often than a clean office. Clean the fans and heatsinks on the same schedule.
Common myths
- Negative pressure always runs hotter. Temperatures depend on the total airflow and the path it takes.
- Equal fan counts mean balanced pressure. Fan speed, filters and restrictions change the balance.
- More exhaust fans always lower temperatures. The air path matters more than the fan count.
- Hot air rising matters more than fan direction. Fans usually dominate the airflow inside a case.
Safety
- Unplug the PC before you rearrange fans or cables.
For fan speed control once your layout is set, see how to set a fan curve for your CPU cooler. For drive airflow, see hard drive temperatures and cooling.