PC Cooling

How to Replace Thermal Paste on Your CPU

Step-by-step CPU thermal paste replacement: what a kit contains, how much paste to use, how to remount the cooler and how to check temperatures.

On this page
  1. When a repaste is worth doing
  2. What’s in a thermal paste replacement kit
  3. Choosing a paste
  4. Before you start
  5. Step-by-step repaste
  6. Checking your temperatures afterward
  7. Common mistakes
  8. Safety

Thermal paste fills the tiny gaps between a CPU and its cooler so heat can move between them. Over time, paste can dry out or pump out from under the cooler, and a fresh application can bring temperatures back down. You also need to repaste whenever you remove the cooler. This guide covers the kit, the paste and the steps. For timing, see how often to change thermal paste.

When a repaste is worth doing

  • You have removed or remounted the cooler. Always repaste then, because the old compound has been disturbed.
  • Load temperatures are climbing after you cleaned the dust out of the cooler and fans.
  • The CPU throttles under load, or the fans are louder than they used to be.
  • You bought a used CPU or cooler and don’t know its paste history.

What’s in a thermal paste replacement kit

A typical kit includes a syringe of thermal paste, isopropyl alcohol wipes, a plastic spatula and a lint-free cloth. Some kits add a two-step cleaner, such as ArctiClean, for stubborn old paste. The extras are optional. You can use your own isopropyl alcohol and lint-free cloths.

Use isopropyl alcohol at 90% or higher. 99% is ideal for cleaning. Sealed paste keeps for a few years, but the shelf life varies by product, so check the date on the tube.

Choosing a paste

Popular pastes include Arctic MX-4 and MX-6, Noctua NT-H1 and NT-H2, Thermal Grizzly Kryonaut, and Gelid GC-Extreme. They’re widely used and easy to find.

Manufacturer W/mK ratings don’t compare well between brands, because each maker measures differently. Don’t pick a paste on that number alone. Most modern pastes, such as MX-4, need no cure time, so you can power up and run the PC right after.

Liquid metal conducts electricity and attacks aluminium, so it isn’t a beginner’s choice. Phase-change pads, such as Honeywell PTM7950, are an alternative that resists pump-out and lasts longer.

Before you start

  • Work on a clean, well-lit table with room around the case.
  • Gather a screwdriver for the cooler’s mounting hardware, the isopropyl alcohol, the lint-free cloth and the new paste.
  • Check that the PC is off, the PSU switch is off and the power cord is unplugged.
  • Read your cooler’s manual for its removal and mounting order.

Step-by-step repaste

1. Warm up the paste (optional)

Run the PC for a few minutes first. Warm paste softens and releases more easily. Then shut the PC down.

2. Power down and unplug

Switch off the PSU and unplug the power cord. Touch bare case metal before you handle parts, to discharge any static.

3. Remove the cooler

Loosen the cooler’s mounting screws a few turns at a time, in a cross pattern, so the pressure comes off evenly. Then gently twist the cooler side to side to break the paste seal before you lift. On AM4 (PGA) CPUs, pulling straight up can lift the CPU out of its socket, so twist and lift slowly.

4. Clean the old paste off

Wipe the CPU and the cooler’s base with isopropyl alcohol and the lint-free cloth. Keep going until no residue remains on either surface. Let the alcohol evaporate fully before you apply new paste. Isopropyl alcohol is flammable, so keep it away from heat and sparks.

5. Apply the new paste

For most mainstream CPUs, one pea-sized dot of about 4 to 5 mm in the center works well. Large rectangular heat spreaders, such as LGA1700, LGA1851 and AM5 chips, need more coverage. For those, use an X, a line or a five-dot pattern. The pattern matters less than the right amount and full coverage. Too much paste spills over the edges and makes a mess, so less is more.

6. Remount the cooler

Set the cooler back on the CPU and tighten the screws diagonally, a few turns at a time, until they are snug. Don’t overtighten them.

7. Reconnect and power up

Reconnect the cooler’s fan and any other cables, then plug in the PC and power it on.

Checking your temperatures afterward

Run a sustained load and check the readings in HWiNFO or a similar monitor. Load temperatures should match or beat your earlier readings. If they’re worse, check that the cooler is seated evenly and that the paste covers the whole CPU.

Record your idle and load temperatures after the repaste, so you have a baseline to compare against later. The paste timing guide lists the signs to watch for.

Common mistakes

  • Using more paste. Extra paste spreads over the edges and doesn’t help. The right amount is whatever fills the gap.
  • Reusing old paste. Remove it and apply fresh paste whenever the cooler comes off.
  • Wiping off pre-applied paste. Pre-applied paste on a new cooler is fine. Use it as it is, and don’t add more on top.
  • Assuming all paste conducts electricity. Most pastes don’t. Liquid metal does.

Safety

  • Unplug the PC every time you remove the cooler.
  • Isopropyl alcohol is flammable. Work with the PC unplugged and keep flames and sparks away.
  • Liquid metal conducts electricity and attacks aluminium. Avoid it unless you have experience, and keep it away from aluminium heatsinks.

The complete guide to pc cooling

Desktop PC Cooling Explained: Air, AIO and Custom Loops
Read the guide

Keep exploring

Guides from other topics

All topics →