PC Cooling

What do heatsinks do?

A heatsink pulls heat away from a chip and spreads it into air or liquid through fins. Learn how heatsinks work, what they're made of and where PCs use them.

On this page
  1. How a heatsink moves heat
  2. Materials: copper and aluminium
  3. Heat pipes and vapor chambers
  4. Passive and active heatsinks
  5. Where PCs use heatsinks
  6. What heatsinks can’t do
  7. Common misconceptions
  8. Safety

A heatsink pulls heat away from a hot chip and spreads it across a large metal surface. Air or liquid then carries the heat away. That keeps the part from slowing down to protect itself, which is called throttling, and from being damaged by sustained heat.

How a heatsink moves heat

A heatsink works in three steps:

  1. Conduction: the metal base touches the hot part, and heat flows into the metal. Thermal paste or pads fill the tiny gaps between the two surfaces, because air is a poor conductor of heat.
  2. Spreading: fins or pins extend from the base. They expose far more metal to the air than a flat surface would.
  3. Convection: air moving past the fins carries the heat away.

A heatsink can’t cool a part below the temperature of the air around it. It moves heat, and the air has to carry that heat away.

Materials: copper and aluminium

Copper conducts heat well, at roughly 400 W/m·K. Aluminium conducts less, roughly 205 to 237 W/m·K, but it is lighter and cheaper. Many CPU coolers combine the two: a copper base or heat pipes, with aluminium fins. The copper picks up heat quickly, and the aluminium spreads it over a large area at lower cost.

Heat pipes and vapor chambers

A heat pipe is a sealed copper tube with a wick and a small amount of working fluid, usually water, at low pressure. The fluid evaporates at the hot end, travels to the cool end and condenses there, giving up its heat to the fins. That moves heat much faster than solid copper can. Typical CPU cooler heat pipes are 6 mm or 8 mm in diameter.

A vapor chamber is a flat version of the same idea. It spreads heat across a wide area, which is why vapor chambers are common on graphics cards. Heat pipes work in most orientations, though a hot end sitting above the fins can cost a little performance.

Passive and active heatsinks

A passive heatsink relies on natural airflow. It’s silent and has no moving parts, but it depends on case airflow to carry heat away. An active heatsink adds a fan to push more air through the fins.

Passive CPU coolers can work for low-power chips, but they depend heavily on case airflow. A passive cooler that doesn’t suit the case can let the CPU run hot. For most desktop CPUs, an active cooler is the safer default.

Denser fins need fans that can push air through them. Look at a fan’s static pressure rating when you pair it with a dense heatsink or radiator.

Where PCs use heatsinks

Many parts in a PC use heatsinks or spreaders:

  • CPU: the cooler, whether air, AIO or custom loop.
  • Graphics card: a heatsink with fans, often with vapor chambers.
  • VRMs: the power-circuit heatsinks near the CPU socket. See VRM heatsinks.
  • Chipset: a small heatsink on many boards.
  • M.2 SSDs: a heatsink on the drive or the board. See does an SSD really need a heatsink.
  • RAM: heat spreaders. On DDR4 they mostly add looks. DDR5 modules have an on-module power chip, so their spreaders matter more.

Hard drives run warm but usually rely on airflow rather than heatsinks. See hard drive temperatures and cooling.

What heatsinks can’t do

  • They don’t create cold. They move heat, and they can’t lower a part’s temperature below the surrounding air.
  • Bigger isn’t always better. A large heatsink with poor airflow or poor contact can run hotter than a smaller one with good airflow.
  • They don’t stay clean on their own. Dust clogs fins quickly and cuts performance, so clean them regularly.

Common misconceptions

  • Heatsinks produce cold. They only move heat.
  • Bigger or heavier always means better. Airflow and contact matter just as much.
  • Heatsinks never need cleaning. Dust clogs fins, so clean them.
  • RAM heat spreaders are always essential. On DDR4 they’re mostly cosmetic.

Safety

  • Fins can be sharp, and heatsinks get hot after a sustained load. Handle them with care, and let the PC cool before you touch them.

For the cooler types that use these heatsinks, see the PC cooling guide. For how paste fills the gap between a CPU and its cooler, see how to replace thermal paste on your CPU.

The complete guide to pc cooling

Desktop PC Cooling Explained: Air, AIO and Custom Loops
Read the guide

Keep exploring

Guides from other topics

All topics →