PC Cooling

How to Set a Fan Curve for Your CPU Cooler in BIOS or Software

Set a CPU cooler fan curve in BIOS or software. Learn 4-pin vs 3-pin control, a sample curve, hysteresis for quieter fans, and how to test under load.

On this page
  1. What a fan curve does
  2. Check your headers first
  3. Setting the curve in BIOS
  4. Setting the curve in software
  5. A sample CPU curve
  6. Smoothing the curve: hysteresis and averaging
  7. AIO pumps and radiator fans
  8. Test the curve under load
  9. Common mistakes
  10. Troubleshooting
  11. Safety

A fan curve links fan speed to a temperature, so the fan spins faster as the CPU gets hotter. The default curve on most boards is close to linear, which means the fans react to every small change, including brief spikes. A tuned curve can run quieter with little cost in temperature. This guide covers how to check your headers, set the curve in BIOS or software, and test the result.

What a fan curve does

A fan curve is a graph. The horizontal axis is a temperature, and the vertical axis is fan speed as a percentage. Each point says how fast the fan should run at a given temperature. The board reads a sensor, usually the CPU, and applies the curve.

Noise often comes from the speed changing rather than from the speed itself. A curve that reacts to every spike makes the fans speed up and slow down repeatedly. A smoother curve, with a steady base speed and a damped response, sounds more consistent.

Check your headers first

Before you change any curve, confirm how each fan is connected:

  • 4-pin fans use PWM control. Set the header to PWM mode.
  • 3-pin fans use voltage control. Set the header to DC mode.

Then find each fan’s minimum speed. Many fans stall below about 20 to 30 percent PWM. Some fans support a zero-RPM mode, but many don’t, so test before you set a fan to zero. If a fan stalls, raise its minimum.

For the 3-pin case, see 3-pin CPU fan on a 4-pin motherboard.

Setting the curve in BIOS

Most motherboards have a fan curve editor in the BIOS. Menu names vary by vendor:

  • ASUS: Q-Fan
  • MSI: Smart Fan
  • Gigabyte: Smart Fan
  • ASRock: FAN-Tastic Tuning

The menu location also varies by board and BIOS version, so look under the hardware monitor or fan settings. Save your changes before you leave the BIOS, usually with F10.

Setting the curve in software

Software control is convenient because you can adjust curves without rebooting, and some tools can use several sensors at once. Common options include:

  • FanControl (Windows): free and open source, with support for curves, triggers and profiles.
  • Armoury Crate (ASUS), MSI Center (MSI) and Gigabyte Control Center (Gigabyte): vendor tools.
  • Argus Monitor (Windows): a commercial option with fan curve support.
  • CoolerControl and lm-sensors / fancontrol (Linux): for Linux systems.

Software can conflict with the BIOS. If both control the same fan, the results can be unpredictable. Pick one place to set each fan’s curve.

A sample CPU curve

This curve is a starting point, not a rule. Tune it for your CPU and cooler:

CPU temperature Fan speed
40 °C 30%
60 °C 50%
75 °C 70%
85 to 90 °C 100%

Use a curve that stays low at idle and reaches full speed only near the top of the range. Adjust the points after you test.

Smoothing the curve: hysteresis and averaging

Two settings help the fans stop reacting to every spike:

  • Hysteresis: a small temperature or time delay before the fan changes speed. A 2 to 5 °C band or a few seconds is a typical starting point.
  • Averaging: many Ryzen temperatures spike quickly. A smoothed or averaged sensor reacts less to short bursts.

A useful pattern is a steady base speed at low temperatures, a gentle slope through the middle, and a steeper slope only near the top. This keeps the fan speed more constant during gaming and everyday work.

AIO pumps and radiator fans

An AIO pump should run at a fixed speed, usually 100 percent or the speed the maker recommends. Don’t put the pump on a curve that can drop to 0 percent, because a stopped pump can overheat the CPU under load.

For the radiator fans, use the coolant temperature if your software or BIOS offers it. A common setup runs the fans low near 30 °C coolant and high near 40 °C coolant, though the exact values depend on the cooler.

For pump noise, see AIO pump noise.

Test the curve under load

A curve should be tested under a sustained load, such as Cinebench or Prime95, while you watch HWiNFO.

  1. Run the load for 10 minutes or more.
  2. Record peak CPU temperature, fan speeds and whether the CPU throttles.
  3. Listen for pulsing or surging fan noise.
  4. Repeat the test on a warm day or after the PC has been running for a while, because case heat changes the results.

Don’t chase a single temperature number. Modern CPUs are designed to run near their limit. Ryzen 7000 and 9000 chips boost until they reach about 95 °C, and Intel chips have a limit around 100 °C. A reading near those figures isn’t a fault. Judge the curve by stability, noise and throttling.

Common mistakes

  • Running fans at 100 percent all the time. It’s loud, and it isn’t the best setting.
  • Expecting an instant response to every spike. Some delay is intentional, and it reduces noise.
  • Letting BIOS and software control the same fan. Choose one.
  • Expecting a flat curve to lower the maximum temperature. A flat curve changes noise below the limit, not the peak.

Troubleshooting

  • Software doesn’t detect a fan or sensor: run the tool as an administrator. On Windows, a right-click and “Run as administrator” often gives it the access it needs.
  • The BIOS doesn’t offer the mode you need: check whether PWM or DC control is disabled for that header. Some boards default to automatic modes that interfere with software control.
  • Strange behavior after many changes: a Clear CMOS resets the whole BIOS to factory settings, so use it as a last resort and note your settings first.

Safety

  • Never set the pump or the CPU fan to a speed that can stop it under load.
  • Power off and unplug before you connect or disconnect fan headers.

For the header basics, see 3-pin CPU fan on a 4-pin motherboard. For the full cooler setup, see how to install an AIO liquid cooler.

The complete guide to pc cooling

Desktop PC Cooling Explained: Air, AIO and Custom Loops
Read the guide

Keep exploring

Guides from other topics

All topics →