Quick answer: start with the header and the cable
Most “no lights” problems come from the connector, the header or the software, more often than from a dead device. Work through the steps in order, and power off before you reseat anything.
Step 1: Check the connector and header type
- A 3-pin 5V ARGB device goes on an ARGB header. A 4-pin 12V RGB device goes on a 12V RGB header.
- Read the labels on the board. The ARGB and RGB headers guide lists the names by brand.
- A 5V device run on a 12V header is usually permanently damaged. Never test one on the other kind of header.
Step 2: Reseat every connection
With the PC off and the PSU switched off:
- Push each cable fully into its header. Loose daisy-chain joints are a common cause.
- Check that the arrow on the plug lines up with the +5V or +12V pin.
- If you use a hub, check that it has SATA or Molex power and a data cable to a board header or USB.
Step 3: Check the BIOS LED settings
LEDs can be switched off in the BIOS, and software can’t override that setting.
- ASUS: check RGB LED Lighting under Onboard Devices Configuration.
- MSI: check the EZ LED Control toggle.
- Gigabyte and ASRock: check the LED options under the onboard device settings. Names vary by BIOS version.
If your hub has a mode button or an “MB sync” switch, set it to motherboard mode.
Step 4: Check the software
- Run one RGB app at a time. Armoury Crate, MSI Center, GCC, Polychrome, iCUE, SignalRGB and OpenRGB can all conflict with each other.
- Confirm the device is on the software’s compatibility list.
- If it still fails, do a clean reinstall of the vendor software. For ASUS, use the Armoury Crate Uninstall Tool.
Step 5: Swap a device or header to find the fault
Plug the device into a different header of the same type, or plug a known-working device into the original header.
- If the device works in another header, the original header or its software is the likely problem.
- If the device fails everywhere, it is probably dead.
Step 6: Update BIOS and firmware
A BIOS update or firmware update can fix device detection. Check the board’s support page for an update that mentions the problem you see, and follow the instructions exactly. Update only when you have a reason to.
Step 7: Reset carefully
- Clearing the CMOS resets every BIOS setting to its default, including the memory profile and boot order. Note your settings first.
- A CMOS clear can also fix an LED setting that’s stuck off. It resets everything else too.
- To drain leftover power, unplug the PSU and hold the power button for about 10 to 30 seconds.
Lights on, but wrong colours
- Look for a bent pin or a damaged cable at the header and at the plug.
- Check the colour order setting in the software. Some devices show the wrong colours until you set the RGB or GRB order.
RAM RGB that doesn’t show
RAM lighting follows the board’s software only when the kit is compatible with that software. Check the kit’s listing for the board’s lighting system. Then update the BIOS and the board’s software, and run the software as administrator if devices still don’t appear.
When a device is probably damaged
Stop testing, and consider repair or replacement, if:
- A 5V device was run on a 12V header. It is usually permanently damaged.
- The device gets hot or smells of burning. Power the PC off at once.
- The device fails on every header, in every PC.
Safety
- Turn off the PSU switch before you reseat RGB cables.
- Never test a 5V device on a 12V header.
- Don’t force a plug that doesn’t fit. Keyed connectors are there to prevent damage.
For ASUS boards, see how to control RGB on an ASUS motherboard. For LEDs that stay on after shutdown, see how to turn off motherboard LEDs. For overloaded chains, see how many ARGB lights you can daisy chain.